Polymer thermal analysis

Optically active polymers play a very important role in our modem society. The specialities of optically active polymers are known with their various characteristics as occurred naturally in mimicry. The present review describes the monomers and synthesis of optically active polymers from its helicity, internal compounds nature, dendronization, copolymerization, side chromophoric groups, chiral, metal complex and stereo-specific behaviour. The various properties like nonlinear optical properties of azo-polymers, thermal analysis, chiroptical properties, vapochromic behaviour, absorption and emission properties, thermosensitivity, chiral separation, fabrication and photochromic property are explained in detail. This review is expected to be interesting and useful to the researchers and industry personnel who are actively engaged in research on optically active polymers for versatile applications. 

Affolter S, Schmid M. Interlaboratory tests on polymers thermal analysis. Int Polym Anal Charact 2000 6 35-57. 

The definition of polymer thermal stabiUty is not simple owing to the number of measurement techniques, desired properties, and factors that affect each (time, heating rate, atmosphere, etc). The easiest evaluation of thermal stabiUty is by the temperature at which a certain weight loss occurs as observed by thermogravimetric analysis (tga). Early work assigned a 7% loss as the point of stabiUty more recentiy a 10% value or the extrapolated break in the tga curve has been used. A more reaUstic view is to compare weight loss vs time at constant temperature, and better yet is to evaluate property retention time at temperature one set of criteria has been 177°C for 30,000 h, or 240°C for 1000 h, or 538°C for 1 h, or 816°C for 5 min (1). 

Thermodynamic Properties. The thermodynamic melting point for pure crystalline isotactic polypropylene obtained by the extrapolation of melting data for isothermally crystallized polymer is 185°C (35). Under normal thermal analysis conditions, commercial homopolymers have melting points in the range of 160—165°C. The heat of fusion of isotactic polypropylene has been reported as 88 J/g (21 cal/g) (36). The value of 165 18 J/g has been reported for a 100% crystalline sample (37). Heats of crystallization have been determined to be in the range of 87—92 J/g (38). 

Thermal analysis iavolves techniques ia which a physical property of a material is measured agaiast temperature at the same time the material is exposed to a coatroUed temperature program. A wide range of thermal analysis techniques have been developed siace the commercial development of automated thermal equipment as Hsted ia Table 1. Of these the best known and most often used for polymers are thermogravimetry (tg), differential thermal analysis (dta), differential scanning calorimetry (dsc), and dynamic mechanical analysis (dma). 

Melting temperatures of as-polymerized powders are high, ie, 198—205°C as measured by differential thermal analysis (dta) or hot-stage microscopy (76). Two peaks are usually observed in dta curves a small lower temperature peak and the main melting peak. The small peak seems to be related to polymer crystallized by precipitation rather than during polymerization. 

Crystallization kinetics have been studied by differential thermal analysis (92,94,95). The heat of fusion of the crystalline phase is approximately 96 kj/kg (23 kcal/mol), and the activation energy for crystallization is 104 kj/mol (25 kcal/mol). The extent of crystallinity may be calculated from the density of amorphous polymer (d = 1.23), and the crystalline density (d = 1.35). Using this method, polymer prepared at —40° C melts at 73°C and is 38% crystalline. Polymer made at +40° C melts at 45°C and is about 12% crystalline. 

Viscoelastic phenomena always involve the change of properties with time and, therefore, the measurements of viscoelastic properties of solid polymers may be called dynamic mechanical. Dynamic mechanical thermal analysis (DMTA) is a very useful tool for studying... 

Thermal analysis helps in measuring the various physical properties of the polymers. In this technique, a polymer sample is subjected to a controlled temperature program in a specific atmosphere and properties are measured as a function of temperature. The controlled temperature program may involve either isothermal or linear rise or fall of temperature. The most common thermoanalytical techniques are (1) differential scanning analysis (DSC), (2) thermomechanical analysis (TMA), and (3) thermogravimetry (TG). 

Thermal analysis of homopolymer samples are simpler than those of blends. Separate thermal analysis of individual polymer components are made before doing the same for a blend in order to get more accurate and proper information on thermal characteristics. 

Thermogravimetric analysis has also been used in conjunction with other techniques, such as differential thermal analysis (DTA), gas chromatography, and mass spectrometry, for the study and characterisation of complex materials such as clays, soils and polymers.35... 

Dynamic differential thermal analysis is used to measure the phase transitions of the polymer. IR is used to determine the degree of unsaturation in the polymer. Monitoring of the purity and raw is done commercially using gas phase chromatography for fractionization and R1 with UV absorption at 260 nanometers for polystyrene identification and measurement Polystyrene is one of the most widely used plastics because of fabrication ease and the wide spectrum of properties possible. Industries using styrene-based plastics are packaging, appliance, construction, automotive, radio and television, furniture, toy, houseware and baggage. Styrene is also used by the military as a binder in expls and rocket propints... 

Levi, Literature Survey on Thermal Degradation, Thermal Oxidation, and Thermal Analysis of High Polymers , PLASTEC Note 7 (1963)... 

Literature Survey on Thermal Degradation, Thermal Oxidation, and Thermal Analysis of High Polymers. Ill , PLASTEC Note 20 (1969) 29) N T. Baldanza, Literature Search Injection Molding Processing Parameters , PLASTEC Note 21 (1969) 30) A.H. Landrock, Polyurethane... 

---