Poly polymer surfaces

The earliest SFA experiments consisted of bringing the two mica sheets into contact m a controlled atmosphere (figure Bl.20.61 or (confined) liquid medium [14, 27, 73, 74 and 75]. Later, a variety of surfactant layers [76, 77], polymer surfaces [5, 9, fO, L3, 78], poly electrolytes [79], novel materials [ ] or... 

Other SSIMS studies of polymer surfaces have included perfluorinated polyether [3.21], low-density polyethylene [3.22], poly(ethylene terephthalate) [3.23], and the oxidation of polyetheretherketone [3.24]. 

Convincing evidence for a surface erosion process is shown in Fig. 8, which shows the concomitant release of the incorporated marker, methylene blue, release of the anhydride excipient hydrolysis product, succinic acid, and total weight loss of the device. According to these data, the release of an incorporated drug from an anhydride-catalyzed erosion of poly (ortho esters) can be unambiguously described by a polymer surface erosion mechanism. 

The next two examples illustrate more complex surface reaction chemistry that brings about the covalent immobilization of bioactive species such as enzymes and catecholamines. Poly [bis (phenoxy)-phosphazene] (compound 1 ) can be used to coat particles of porous alumina with a high-surface-area film of the polymer (23). A scanning electron micrograph of the surface of a coated particle is shown in Fig. 3. The polymer surface is then nitrated and the arylnitro groups reduced to arylamino units. These then provided reactive sites for the immobilization of enzymes, as shown in Scheme III. 

Polymer properties, influence of ions, 258 Polymer surface reactions, kinetics, 322-323 Polymer transformation reactions configurational effect, 38 conformational effects, 38 hydrolysis of polyfmethyl methacrylate), 38 neighboring groups, 37-38 quaternization of poly(4-vinyl pyridine), 37-38 Polymerization, siloxanes, 239... 

Direct fluorination of polymer or polymer membrane surfaces creates a thin layer of partially fluorinated material on the polymer surface. This procedure dramatically changes the permeation rate of gas molecules through polymers. Several publications in collaboration with Professor D. R. Paul62-66 have investigated the gas permeabilities of surface fluorination of low-density polyethylene, polysulfone, poly(4-methyl-1 -pentene), and poly(phenylene oxide) membranes. 

Another interesting and possibly useful result of fluorination of XeF2-treated polymer surfaces is decreased gas permeability. For example, fluorinated poly-... 

Polymer surfaces, preparation of, 11 846 Polymer suspensions, poly(ethylene oxide) resin, 10 683... 

TiCU readily functionalizes hydrophilic polymers such as poly(vinyl alcohol), m-ciesol novolac and methacrylic acid copolymers as well as moderately hydrophobic polymers such as poly(methyl methacrylate), poly(vinyl acetate), poly(benzyl methacrylate) and fully acetylated m-cresol novolac. HCI4 did not react with poly(styrene) to form etch resistant films indicating that very hydrophobic films follow a different reaction pathway. RBS analysis revealed that Ti is present only on the surface of hydrophilic and moderately hydrophobic polymer films, whereas it was found diffused through the entire thickness of the poly(styrene) films. The reaction pathways of hydrophilic and hydrophobic polymers with HCI4 are different because TiCl is hydrolysed by the surface water at the hydrophilic polymer surfaces to form an etch resistant T1O2 layer. Lack of such surface water in hydrophobic polymers explains the absence of a surface TiC>2 layer and the poor etching selectivities. 

Fig.5 Schematic diagram showing a comb-like poly(ethylene oxide) gradient produced on a polymer surface. (Reproduced with permission from [24])...

Alkyl monoesters of poly(vinyl methyl ether-maleic anhydride) (PVM-MA) are bioerodible acidic polymers that are used to control drug release. In biological fluids with poor buffering capacity, drug release from the polymers and their dissolution are slowed owing to the lower pH on the polymer surface. We studied whether the release of timolol from matrices of monoisopropyl ester of PVM-MA in vitro and in vivo in rabbits eyes could be affected by disodium phosphate in the matrices. Addition of disodium phosphate to the matrices doubled the release rate of timolol in vitro, but it did not affect the bulk pH of the dissolution medium. On the basis of the timolol concentrations in the tear fluid and in systemic circulation, disodium phosphate seems to accelerate drug release in vivo also. Disodium phosphate probably affects the rate of dmg release by increasing the microenvironmental pH on the polymer surface. 

---