Poly molecular weight

Fig. XI-7. Volume fraction profile of 280,000-molecular-weight poly(ethylene oxide) adsorbed onto deuterated polystyrene latex at a surface density of 1.21 mg/m and suspended in D2O, from Ref. 70.

A graphical method, proposed by Zimm (thus tenned the Zinnn plot), can be used to perfomi this double extrapolation to detemiine the molecular weight, the radius of gyration and the second virial coefficient. An example of a Zinnn plot is shown in figure Bl.9.6 where the light scattering data from a solution of poly... 

The second category of polymerization reactions does not involve a chain reaction and is divided into two groups poly addition and poly condensation [4]. In botli reactions, tire growth of a polymer chains proceeds by reactions between molecules of all degrees of polymerization. In polycondensations a low-molecular-weight product L is eliminated, while polyadditions occur witliout elimination ... 

Figure C2.1.8. Reduced osmotic pressure V l(RTc as a function of the polymer weight concentration for solutions of poly(a-metliylstyrene) in toluene at 25 °C. The molecular weight of poly(a-metliylstyrene) varies...

Mono- and di saccharides are colourless solids or sjrrupy liquids, which are freely soluble in water, practically insoluble in ether and other organic solvents, and neutral in reaction. Polysaccharides possess similar properties, but are generally insoluble in water because of their high molecular weights. Both poly- and di-saccharides are converted into monosaccharides upon hydrolysis. 

At 25°C, the Mark-Houwink exponent for poly(methyl methacrylate) has the value 0.69 in acetone and 0.83 in chloroform. Calculate (retaining more significant figures than strictly warranted) the value of that would be obtained for a sample with the following molecular weight distribution if the sample were studied by viscometry in each of these solvents ... 

As we did in the case of relaxation, we now compare the behavior predicted by the Voigt model—and, for that matter, the Maxwell model—with the behavior of actual polymer samples in a creep experiment. Figure 3.12 shows plots of such experiments for two polymers. The graph is on log-log coordinates and should therefore be compared with Fig. 3.11b. The polymers are polystyrene of molecular weight 6.0 X 10 at a reduced temperature of 100°C and cis-poly-isoprene of molecular weight 6.2 X 10 at a reduced temperature of -30°C. 

The phenomena we discuss, phase separation and osmotic pressure, are developed with particular attention to their applications in polymer characterization. Phase separation can be used to fractionate poly disperse polymer specimens into samples in which the molecular weight distribution is more narrow. Osmostic pressure experiments can be used to provide absolute values for the number average molecular weight of a polymer. Alternative methods for both fractionation and molecular weight determination exist, but the methods discussed in this chapter occupy a place of prominence among the alternatives, both historically and in contemporary practice. 

If the poorer solvent is added incrementally to a system which is poly-disperse with respect to molecular weight, the phase separation affects molecules of larger n, while shorter chains are more uniformly distributed. These ideas constitute the basis for one method of polymer fractionation. We shall develop this topic in more detail in the next section. 

The solute molecular weight enters the van t Hoff equation as the factor of proportionality between the number of solute particles that the osmotic pressure counts and the mass of solute which is known from the preparation of the solution. The molecular weight that is obtained from measurements on poly disperse systems is a number average quantity. 

We shall be interested in determining the effect of electrolytes of low molecular weight on the osmotic properties of these polymer solutions. To further simplify the discussion, we shall not attempt to formulate the relationships of this section in general terms for electrolytes of different charge types-2 l, 2 2, 3 1, 3 2, and so on-but shall consider the added electrolyte to be of the 1 1 type. We also assume that these electrolytes have no effect on the state of charge of the polymer itself that is, for a polymer such as, say, poly (vinyl pyridine) in aqueous HCl or NaOH, the state of charge would depend on the pH through the water equilibrium and the reaction... 

Table 9.3 lists the intrinsic viscosity for a number of poly(caprolactam) samples of different molecular weight. The M values listed are number average figures based on both end group analysis and osmotic pressure experiments. Tlie values of [r ] were measured in w-cresol at 25°C. In the following example we consider the evaluation of the Mark-Houwink coefficients from these data. 

Table 9.3 Intrinsic Viscosity as a Function of Molecular Weight for Samples of Poly(caprolactam) ...

The intrinsic viscosity of poly(7-benzyl-L-glutamate) (Mq = 219) shows such a strong molecular weight dependence in dimethyl formamide that the polymer was suspected to exist as a helix which approximates a prolate ellipsoid of revolution in its hydrodynamic behaviorf ... 

The protonated form of poly(vinyl amine) (PVAm—HCl) has two advantages over many cationic polymers high cationic charge densities are possible and the pendent primary amines have high reactivity. It has been appHed in water treatment, paper making, and textiles (qv). The protonated forms modified with low molecular weight aldehydes are usehil as fines and filler retention agents and are in use with recycled fibers. As with all new products, unexpected appHcations, such as in clear antiperspirants, have been found. It is usehil in many metal complexation appHcations (49). 

Polyacetaldehyde, a mbbery polymer with an acetal stmcture, was first discovered in 1936 (49,50). More recentiy, it has been shown that a white, nontacky, and highly elastic polymer can be formed by cationic polymerization using BF in Hquid ethylene (51). At temperatures below —75° C using anionic initiators, such as metal alkyls in a hydrocarbon solvent, a crystalline, isotactic polymer is obtained (52). This polymer also has an acetal [poly(oxymethylene)] stmcture. Molecular weights in the range of 800,000—3,000,000 have been reported. Polyacetaldehyde is unstable and depolymerizes in a few days to acetaldehyde. The methods used for stabilizing polyformaldehyde have not been successful with poly acetaldehyde and the polymer has no practical significance (see Acetalresins). 

The molecular weight of a polymer can be controlled through the use of a chain-transfer agent, as well as by initiator concentration and type, monomer concentration, and solvent type and temperature. Chlorinated aUphatic compounds and thiols are particularly effective chain-transfer agents used for regulating the molecular weight of acryUc polymers (94). Chain-transfer constants (C at 60°C) for some typical agents for poly(methyl acrylate) are as follows (87) ... 

Poly(dibromostyrene). Poly(dibromostyrene) [62354-98-7] (PDBS) is prepared by the polymerization of dibromostyrene [31780-26-4] (50). Two versions are avaHable. One has a molecular weight of about 10,000, the other a molecular weight of about 80,000. Information comparing the performance of these materials to the performance of the brominated polystyrenes is not avaHable. 

Poly(ethylene oxide)s [25372-68-3] are made by condensation of ethylene oxide with a basic catalyst. In order to achieve a very high molecular weight, water and other compounds that can act as chain terminators must be rigorously excluded. Polymers up to a molecular weight of 8 million are available commercially in the form of dry powders (27). These must be dissolved carefliUy using similar techniques to those used for dry polyacrylamides. Poly(ethylene oxide)s precipitate from water solutions just below the boiling point (see Polyethers, ethylene oxide polymers). 

---