Poly- methyl amino coatings

NBD-amino acids (serine, threonine, valanie, phenylalanine, and histidine) were separated by using a 20 mM ammonium acetate buffer (pH 9.0) containing 10 mM copper acetate, 20 mM L-prolinamide, and 1 mM SDS. The elution order was the L-enantiomer followed by the D-form except in NBD-histidine. Weng et al. [32] described chiral separation of tryptophan on a poly(methyl methacrylate) microfluidic chip coated with bovine serum albumin (32 mm... 

In Japan, poly[ y-methyl-L (or D)-glutamate] is dissolved in dichloro-ethylene and used as the primary coating for materials such as synthetic leathers. The high prices of l and d isomers prohibit wider application of poly(a-amino acids). The dl racemates do not lead to polymers with fiberforming properties. 

APTMOS 3-amino-propyl-trimethoxysilane, AuHFA fluoroalcohol-coated gold nanospheres, BBCB bisbenzocy-clobutene, BCB benzocyclobutene, CA cellulose acetate, CAB cellulose acetate-butyrate, CEE chloroethyl ether, DIMP diisopropyl methylphosphonate, DMMP dimethyl methylphosphonate, EPR epoxidized novolac, IPA isopropanol, OV-225 cyanopropyl methyl phenylmethyl silicone, OV-275 dicyanoallyl sihcone, PAAM polyallylamine hydrochloride, PAPPS propylaminopropyl polysiloxane, PDMS poly(dimethylsiloxane), PECH polyepichlorohydrin, PEG polyethylene glycol, PEI polyethyleneimine, PEO polyethylene oxide, PEVA polyethylene-co-vinyl acetate, PEUT poly(ether urethane), PHEMA poly(2-hydroxyethyl methacrylate), PIB polyisobutylene, PMMA poly(methyl methacrylate), PTMOS propyltrimethoxysilane, PVA polyvinyl alcohol, PVP polyvinylpyrrolidone, SXFA siloxanefluoroalcohol... 

The quality observed with "Mannich" derivatives of polyvinylphenol is affected by the concentration, time of treatment, temperature, pH, and whether or not a final deionized water rinse is used. The results shown in Tables I-III below represent evaluations conducted for poly-[methy1(2-hydroxyethy1)amino]methyl-4-vinylphenol, as shown in Structure I. Post-treatments based on polyvinylphenols overcome deficiencies observed with previous chrome-free rinses, since these systems are reactive and a final water rinse actually improves performance as is illustrated in Table I where the new non-chrome system is evaluated on Bonderite 1000, an iron phosphate conversion coating, as a function of concentration with and without a final water rinse. It is also... 

SMB parameters Cellulose tris(p-methyl- benzoate) beads Poly(N-acryloyl-amino acid ester) silica CSP Cellulose tris(p-methylbenzoate) coated on silica (Chiralcel OJ) Amylose tris(3,5-dimethylphenyl-carbamate) coated on silica (Chiralpak AD)... 

The need for HTPs or HTPBs is often for chemical (e.g., preventing of swelling or oxidation) and mechanical performance. For example, in the petroleum industry dual-layer hollow fiber membranes are used for separation of H2/CO2 and CO2/CH4 gases. These are prepared from solutions of 1 1 PIB/PI blend (e.g. poly[2,2 -(l,3-phenylene)-5,5 -bibenzimidazole] and poly[3,3 4,4 -benzophenone-icira-carboxylic-df-anhydride-co-5(6)-amino-l-(4 -amino-phenyl-l,3-/n-methyl-indane)]).i i The spun hollow fibers are coated by a solution of silicone rubber. The membranes had the desired microstructure. Membrane selectivity of 11.11 and 41.81 was obtained for H2/ CO2 and CO2/CH4, respectively. Furthermore, the new membranes showed good resistance toward COj-induced plasticization. Camacho-Zuniga et al. 

---