Poly acetal trade names

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

The poly(vinyl acetal) prepared from acetaldehyde was developed in the early 1940s by Shawinigan Chemicals, Ltd., of Canada and sold under the trade name Alvar. Early uses included injection-molded articles, coatings for paper and textiles, and replacement for shellac. Production peaked in the early 1950s and then decreased as a result of competition from less expensive resins such as poly(vinyl chloride) (see Vinyl polymers, poly(vinyl chloride)). 

Many plastics are known by more than one name, for example, acetals may be known as polyformaldehyde or, poly-oxymethylene. When this is so then the alternative name(s) should be listed so that cross-referencing is possible. The use of trade names is also prevalent - some of these are shown in Table 3. 

Another commercially derivatized cationic porous glass is produced by Rhone-Poulenc under the trade name SpherosilTM qma. Domard and Rinaudo (56) employed this packing with 0.05 M - 0.2 M ammonium acetate to chromatograph dextran, poly(N-vinylpyrrol idone), PEG, poly(L-lysine), and chitosan. Plate counts were not reported, but typical assay times were apparently 7-9 hrs. While the cationic polymers do not appear to be highly adsorbed, universal calibration plots in 0.2 M ammonium acetate suggest that poly(N-vinylpyrroli-done) is adsorbed. The elution volume of PEG also seems to be sensitive to eluant ionic strength. 

Polyacetal can be divided into two basic types, acetal homoploymer and acetal copolymer. Both homopolymer and copolymer are avaUable in a range of molecular weights (M = 20 000-100 000). The homopolymer is a polymer of formaldehyde with a molecular structure of repeated oxymethylene units (Staudinger, 1932). Large-scale production of poly-formaldehyde, i.e. polyacetal, commenced in 1958 in the USA (US Patent 2 768 994,1956) (British patent 770 717,1957). Delrin (1959) was the first trade mark for this polymer by Du Pont Company. The copolymers were introduced by the Celanese Corporation of America, and the first commercial product named Celcon (1960). One of the major advantages of copolymerization is to stabilize polyacetal because the homopolymer tends to depolymerize and eliminate formaldehyde. The most important stabilization method is structural modification of the polymer by, for example, copolymerization with cyclic ether. 

---