Plug flow reactor idealizations

Residence time behavior of liquid ideal plug flow reactor ideal stirred tank... 

Continuous-Flow Stirred-Tank Reactor. In a continuous-flow stirred-tank reactor (CSTR), reactants and products are continuously added and withdrawn. In practice, mechanical or hydrauHc agitation is required to achieve uniform composition and temperature, a choice strongly influenced by process considerations, ie, multiple specialty product requirements and mechanical seal pressure limitations. The CSTR is the idealized opposite of the weU-stirred batch and tubular plug-flow reactors. Analysis of selected combinations of these reactor types can be useful in quantitatively evaluating more complex gas-, Hquid-, and soHd-flow behaviors. 

An ideal plug flow reactor, for example, has no spread in residence time because the fluid flows like a plug through the reactor (Westerterp etal., 1995). For an ideal continuously stirred reactor, however, the RTD function becomes a decaying exponential function with a wide spread of possible residence times for the fluid elements. 

The riser is a vertical pipe. It usually has s 4- to 5-inch (10 to 1" cm) thick refractory lining for insulation and abrasion resistance. Typical risers are 2 to 6 feet (60 to 180 cm) in diameter and 75 to 120 feet (25 to 30 meters) long. The ideal riser simulates a plug flow reactor, w here the catalyst and the vapor travel the length of the riser with minimum back mixing. 

We now formalize the definition of piston flow. Denote position in the reactor using a cylindrical coordinate system (r, 6, z) so that the concentration at a point is denoted as a(r, 9, z) For the reactor to be a piston flow reactor (also called plug flow reactor, slug flow reactor, or ideal tubular reactor), three conditions must be satisfied ... 

Figure 2.4. Schematic drawings of a cylindrical flow reactor and a batch reactor. In the ideal case the flow reactor operates as a plug-flow reactor in which the gas moves as a piston down through the tube, whereas the ideal batch reactor is a well-mixed Tank Reactor...

Two template examples based on a capillary geometry are the plug flow ideal reactor and the non-ideal Poiseuille flow reactor [3]. Because in the plug flow reactor there is a single velocity, v0, with a velocity probability distribution P(v) = v0 16 (v - Vo) the residence time distribution for capillary of length L is the normalized delta function RTD(t) = T 1S(t-1), where x = I/v0. The non-ideal reactor with the para-... 

It should be noted that the analysis for an ideal-batch reactor is the same as that for a plug-flow reactor (compare Equations 5.43 and 5.61). All fluid elements have the same residence time in both cases. Thus... 

Figure 5.4a compares the profiles for a mixed-flow and plug-flow reactor between the same inlet and outlet concentrations, from which it can be concluded that the mixed-flow reactor requires a larger volume. The rate of reaction in a mixed-flow reactor is uniformly low as the reactant is instantly diluted by the product that has already been formed. In a plug-flow or ideal-batch reactor,... 

High reaction rate in Equation 5.71 is favored by a high concentration of enzymes (CE ) and high concentration of feed (CA). This means that a plug-flow or ideal-batch reactor is favored if both the feed material and enzymes are to be fed to the reactor. 

When choosing between different types of reactors, both continuous and batch reactors were considered from the point of view of the performance of the reactor (continuous plug-flow and ideal batch being equivalent in terms of residence time). If a batch reactor is chosen, it will often lead to a choice of separator for the reactor effluent that also operates in batch mode, although this is not always the case as intermediate storage can be used to overcome the variations with time. Batch separations will be dealt with in Chapter 14. 

As with continuous processes, the heart of a batch chemical process is its reactor. Idealized reactor models were considered in Chapter 5. In an ideal-batch reactor, all fluid elements have the same residence time. There is thus an analogy between ideal-batch reactors and plug-flow reactors. There are four major factors that effect batch reactor performance ... 

Size Comparisons Between Cascades of Ideal Continuous Stirred Tank Reactors and Plug Flow Reactors. In this section the size requirements for CSTR cascades containing different numbers of identical reactors are compared with that for a plug flow reactor used to effect the same change in composition. 

Combinations of Ideal Continuous Stirred Tank Reactors and Plug Flow Reactors... 

REACTOR NETWORKS COMPOSED OF COMBINATIONS OF IDEAL CONTINUOUS STIRRED TANK REACTORS AND PLUG FLOW REACTORS... 

Except for the case of an ideal plug flow reactor, different fluid elements will take different lengths of time to flow through a chemical reactor. In order to be able to predict the behavior of a given piece of equipment as a chemical reactor, one must be able to determine how long different fluid elements remain in the reactor. One does this by measuring the response of the effluent stream to changes in the concentration of inert species in the feed stream—the so-called stimulus-response technique. In this section we will discuss the analytical form in which the distribution of residence times is cast, derive relationships of this type for various reactor models, and illustrate how experimental data are treated in order to determine the distribution function. 

For a few highly idealized systems, the residence time distribution function can be determined a priori without the need for experimental work. These systems include our two idealized flow reactors—the plug flow reactor and the continuous stirred tank reactor—and the tubular laminar flow reactor. The F(t) and response curves for each of these three types of well-characterized flow patterns will be developed in turn. 

The plug flow reactor has a flat velocity profile and no longitudinal mixing. These idealizations imply that all fluid elements leaving the reactor have the same age (T). The F(t) function for this system must then be... 

The responses of this system to ideal step and pulse inputs are shown in Figure 11.3. Because the flow patterns in real tubular reactors will always involve some axial mixing and boundary layer flow near the walls of the vessels, they will distort the response curves for the ideal plug flow reactor. Consequently, the responses of a real tubular reactor to these inputs may look like those shown in Figure 11.3. 

Response of ideal plug flow reactor and real tubular reactor to step and impulse inputs. 

Note that in this case the right side of equation 11.1.68 is zero for t = 0 and unity for t = 00. Figure 11.9 contains several F(t) curves for various values of n. As n increases, the spread in residence time decreases. In the limit, as n approaches infinity the F(t) curve approaches that for an ideal plug flow reactor. If the residence time distribution function given by 11.1.69 is differentiated, one obtains an... 

---