Plant trays

Use cutlery, boxes, flowers pots, seedling plant trays, golf tees, vending cups, pens... 

In such a plant the gas stream passes through a series of fractionating columns in which liquids are heated at the bottom and partly vaporised, and gases are cooled and condensed at the top of the column. Gas flows up the column and liquid flows down through the column, coming into close contact at trays in the column. Lighter components are stripped to the top and heavier products stripped to the bottom of the tower. 

Ethylbenzene Separation. Ethylbenzene [100-41-4] which is primarily used in the production of styrene, is difficult to separate from mixed Cg aromatics by fractionation. A column of about 350 trays operated at a refluxTeed ratio of 20 is required. No commercial adsorptive unit to accomplish this separation has yet been installed, but the operation has been performed successhiUy in pilot plants (see Table 5). About 99% of the ethylbenzene in the feed was recovered at a purity of 99.7%. This operation, the UOP Ebex process, requires about 40% of the energy that is required by fractional distillation. 

Sodium Bicarbonate. Many soda ash plants convert a portion of their production to sodium bicarbonate [144-55-8], NaHCO. Soda ash is typically dissolved, carbonated, and cooled to crystallize sodium bicarbonate. The mother Hquor is heated and recycled. The soHd bicarbonate is dried in flash or tray driers, screened, and separated into various particle size ranges. Bicarbonate markets include food, pharmaceuticals, catde feed, and fire extinguishers. U.S. demand was approximately 320,000 t in 1989 world demand was estimated at one million metric tons. 

Mercury spills should be cleaned up immediately by use of a special vacuum cleaner. The area should then be washed with a dilute calcium sulfide solution. Small quantities of mercury can be picked up by mixing with copper metal granules or powder, or with zinc granules or powder. To avoid or minimize spills, some plants use steel trays as pallets so that a spih, whether of mercury or a mercury compound, is contained on the steel tray. 

In general, plants using SO2 gas derived from metallic sulfides, spent acids, or gypsum anhydrite purify the gas stream before drying it by cold, ie, wet, gas purification. Various equipment combinations including humidification towers, reverse jet scmbbers, packed gas cooling towers, impingement tray columns and electrostatic precipitators are used to clean the gas. 

Cast-iron column shells are satisfactory, but stainless-steel bubble or valve trays are preferred. A flow sheet of a typical tar acid extraction and refining plant is shown in Figure 3. 

Refractories. Its low coefficient of expansion, high thermal conductivity, and general chemical and physical stabihty make sihcon carbide a valuable material for refractory use. Suitable apphcations for sihcon carbide refractory shapes include boiler furnace walls, checker bricks, mufflers, kiln furniture, furnace skid rails, trays for zinc purification plants, etc (see Refractories). 

The lye boHer is usuaHy steam heated but may be direct-fired. Separation efficiency may be iacreased by adding a tower section with bubble-cap trays. To permit the bicarbonate content of the solution to buHd up, many plants are designed to recirculate the lye over the absorber tower with only 20—25% of the solution flowing over this tower passiag through the boHer. Several absorbers may also be used ia series to iacrease absorptioa efficieacies. 

The propylene fractionator operates at a pressure of 1.8 to 2.0 MPa with more than 160 trays required for a high purity propylene product. Often a two-tower design is employed when polymer grade (99.5%+) is required. A pasteurization section may also be used when high purity is required. The bottoms product contains mainly propane that can be recycled to the cracking heaters or used as fuel. Typical tower dimensions and internals for a 450,000 t/yr ethylene plant with naphtha feed are summarized in Table 7. 

FIG. 14-79 Cost of trays in plate towers. Price includes tray deck, bubble caps, risers, downcomers, and structural-steel parts. The stainless steel designated is type 410 Peters and Timmerhaus, Plant Design and Economics for Cbemical Engineers, 4th ed., McGraw-Hill, New York, 1.9.91). 

FIG. 14-81 Fabricated costs and installation time of towers. Costs are for shell with two beads and sldrt, but without trays, packing, or connections. (Peters and Timmerhatis, Plant Design and Economics for Chemical Engineers, 4th ed., McGraw-Hill, New Yoik, 1991. )... 

By far the greatest number of instaUations is for the removal or recoveiy of mostly small concentrations of acidic and other components from air, hydrocarbons, and hydrogen. Hundreds of such plants are in operation, many of them of great size. They mostly employ either packed or tray towers. Power requirements for such equipment are small. When the presence of solid impurities could clog the equipment or when the pressure drop must be low, spray towers are used in spite of their much larger size for a given capacity and scrubbing efficiency. 

Some performance data of plants with DEA are shown in Table 23-11. Both the absorbers and strippers have trays or packing. Vessel diameters and allowable gas and liquid flow rates are estabhshed by the same correlations as for physical absorptions. The calciilation of tower heights utilizes data of equilibria and enhanced mass-transfer coeffi-... 

Analysts must recognize the above sensitivity when identifying which measurements are required. For example, atypical use of plant data is to estimate the tray efficiency or HTU of a distillation tower. Certain tray compositions are more important than others in providing an estimate of the efficiency. Unfortunately, sensor placement or sample port location are usually not optimal and, consequently, available measurements are, all too often, of less than optimal use. Uncertainty in the resultant model is not minimized. 

Forced circ. One theoretical tray Handles high viscous solids-containing liquids Circulation controlled Higher transfer coefficient Highest cost with additional piping and pumps Higher operating cost Requires additional plant area... 

Preliminary Process Flowsheet. This will show major equipment and lines, preliminary equipment details (vessel diameter, number of trays, pump flow and driver horsepower, etc.), major instrumentation, and, it is hoped, have a material balance at the bottom of each drawing with flows keyed to a numbering system on the diagram. The process flowsheets should cover both the process and utility sides of the plant. 

Rigorous calculation results combined with plant data can be used to back calculate column tray efficiencies for... 

Other applications include such diverse items as chemical plant, stacking chairs, swimming pools, trays and sports equipment. 

---