Pinhole

To describe the X-ray imaging system the projection of 3D object points onto the 2D image plane, and nonlinear distortions inherent in the image detector system have to, be modelled. A parametric camera model based on a simple pinhole model to describe the projection in combination with a polynomal model of the nonlinear distortions is used to describe the X-ray imaging system. The parameters of the model are estimated using a two step approach. First the distortion parameters for fixed source and detector positions are calculated without any knowledge of the projection parameters. In a second step, the projection parameters are calculated for each image taken with the same source and detector positions but with different sample positions. 

In Section 2.3.5.1 we have seen that pumping of atoms or molecules through a narrow slit, or small pinhole, whose width (or diameter) is about 20 pm at a pressure of a few torr on the high-pressure side of the aperture produces an efllisive beam. Removal of pressure... 

Capacitors. The outstandingly low dielectric loss of parylenes make them superior candidates for dielectrics in high quality capacitors. Furthermore, their dielectric constant and loss remain constant over a wide temperature range. In addition, they can be easily formed as thin, pinhole-free films. Kemet Flatkaps are fabricated by coating thin aluminum foil with Parylene N on both sides and winding the coated foils in pairs (62). 

Acetic anhydride penetrates the skin quickly and painfully forming bums and bUsters that are slow to heal. Anhydride is especially dangerous to the deUcate tissues of the eyes, ears, nose, and mouth. The odor threshold is 0.49 mg/m, but the eyes are affected by as Httie as 0.36 mg/m and electroencephalogram patterns are altered by only 0.18 mg/m. When handling acetic anhydride, mbber gloves that are free of pinholes are recommended for the hands, as well as plastic goggles for the eyes, and face-masks to cover the face and ears. 

Hot Dip Tin Coating of Steel and Cast Iron. Hot dipping of tin [7440-31 -5] has been largely superseded by electrolytic coating techniques, especially for sheet. However, hot dipping can be the method of choice for complex and shaped parts. Very thin layers of tin are extensively used to passivate steel used for canned goods. Tin is essentially nontoxic, is nearly insoluble in almost all foods, and easily wets and completely covers steel with a pinhole-free coating. 

A number of devices suggest the possibiUty of improvement in the basic limitations of resolution and sensitivity for single-photon instmmentation. One device (24) employs an array of pinholes in a hemispherical shield that Hes inside a hemispherical soHd-state detector array. Simulations and initial experience using early models have suggested that the device could achieve a resolution in the brain of less than 3 or 4 mm and possibly as low as 1 mm. 

The pursuit of further miniaturization of electronic circuits has made submicrometer resolution Hthography a cmcial element in future computer engineering. LB films have long been considered potential candidates for resist appHcations, because conventional spin-coated photoresist materials have large pinhole densities and variations of thickness. In contrast, LB films are two-dimensional, layered, crystalline soHds that provide high control of film thickness and are impermeable to plasma down to a thickness of 40 nm (46). The electron beam polymerization of CO-tricosenoic acid monolayers has been mentioned. Another monomeric amphiphile used in an attempt to develop electron-beam-resist materials is a-octadecylacryUc acid (8). 

Oil Contamination of Helium Gas. For more than 20 years, helium gas has been used in a variety of nuclear experiments to collect, carry, and concentrate fission-recoil fragments and other nuclear reaction products. Reaction products, often isotropically distributed, come to rest in helium at atmospheric concentration by coUisional energy exchange. The helium is then allowed to flow through a capillary and then through a pinhole into a much higher vacuum. The helium thus collects, carries, and concentrates products that are much heavier than itself, electrically charged or neutral, onto a detector... 

Enamel Defects. Characterization of defects in porcelain enamel surfaces frequently requites detailed examination via microscopy to determine the sources of the defects. Defects ate divided into processing and material defects. The greatest number of defects result from processing bhsters, pinholes, black specks, dimples, tool marks, and chipping. Defects often occur from unobserved sources at almost every stage of the enameling process, but they ate not recognizable until the ware is fired. Conscientious process control helps to minimize the incidents of unacceptable finishes. 

As an additional antifoulant measure, SHEs have been coated with a phenolic hning. This provides some degree of corrosion protection as well, but this is not guaranteed due to pinholes in the lining process. 

---