Offset rate

At the cellular level, the major electrophysiological effect appears to be rate-dependent blockade of sodium channels [22]. The onset for this Class I effect (64 + 9% of the final depression of between the first and second beat of the train) was similar to that for Class IB agents [23]. The offset rate (recovery of from rate-dependent depression) for amiodarone was 1.48 s. This value falls between those seen for Class IB agents (200-500 ms) and lA agents (2.3-12.2 s) [23]. Amiodarone inhibited the binding of pH]ba-trochotoxinin A 20a-benzoate to the sodium channel, suggesting that it binds to inactivated sodium channels [24]. 

The greater the undercooling, the more rapidly the polymer crystallizes. This is due to the increased probability of nucleation the more supercooled the liquid becomes. Although the data in Fig. 4.8 are not extensive enough to show it, this trend does not continue without limit. As the crystallization temperature is lowered still further, the rate passes through a maximum and then drops off as Tg is approached. This eventual decrease in rate is due to decreasing chain mobility which offsets the nucleation effect. 

In the most common production method, the semibatch process, about 10% of the preemulsified monomer is added to the deionised water in the reactor. A shot of initiator is added to the reactor to create the seed. Some manufacturers use master batches of seed to avoid variation in this step. Having set the number of particles in the pot, the remaining monomer and, in some cases, additional initiator are added over time. Typical feed times ate 1—4 h. Lengthening the feeds tempers heat generation and provides for uniform comonomer sequence distributions (67). Sometimes skewed monomer feeds are used to offset differences in monomer reactivity ratios. In some cases a second monomer charge is made to produce core—shell latices. At the end of the process pH adjustments are often made. The product is then pumped to a prefilter tank, filtered, and pumped to a post-filter tank where additional processing can occur. When the feed rate of monomer during semibatch production is very low, the reactor is said to be monomer starved. Under these... 

The component with the lower viscosity tends to encapsulate the more viscous (or more elastic) component (207) during mixing, because this reduces the rate of energy dissipation. Thus the viscosities may be used to offset the effect of the proportions of the components to control which phase is continuous (2,209). Frequently, there is an intermediate situation where a cocontinuous or interpenetrating network of phases can be generated by careflil control of composition, microrheology, and processing conditions. Rubbery thermoplastic blends have been produced by this route (212). 

Nitrous oxide produces respiratory depression (38,39). It has been shown to produce a direct myocardial depressant effect in dogs (40) and in humans breathing a 40% N2O/60% oxygen mixture (41) however, this may be offset by the activation of the sympathetic nervous system (42). The combination of nitrous oxide and opioids can produce decreases in myocardial contractiHty, heart rate, and blood pressure (43). 

Nonattamment. EPA issued final rules for the Emission Offset PoHcy governing development in nonattainment areas. A new source must apply the lowest achievable emission rate (LAER) for the problem poUutant and must obtain a more than equivalent offsetting emission reduction from existing sources. Either the existing sources can be owned by the same company, or the reduction can be bought from other companies. In this way, new growth is ahowed while air quahty improvement is achieved. 

In the glass (qv) and ceramic industry (see Ceramics), barite can be used both as a flux, to promote melting at a lower temperature or to increase the production rate, and as an additive to increase the refractive index of glass. The viscosity of barite-containing glass often needs to be raised. Alumina in the form of feldspar is sometimes used. To offset any color produced by iron from the barite addition, more decolorizer may be needed. When properly used, barytes help reduce seed, increase toughness and brilliancy, and reduce annealing time. Barite is also a raw material for the manufacture of other barium chemicals. 

Dilute (1—3%), chloride-containing solutions of either HOCl, hypochlorite, or aqueous base, can be stripped in a column against a current of CI2, steam, and air at 95—100°C and the vapors condensed giving virtually chloride-free HOCl solutions of higher concentration in yields as high as 90% (122—124). Distillation of more concentrated solutions requires reduced pressure, lower temperature, and shorter residence times to offset the increased decomposition rates. 

---