O-ring sealed

Compatibility and Corrosion. Gas turbine fuels must be compatible with the elastomeric materials and metals used in fuel systems. Elastomers are used for O-rings, seals, and hoses as well as pump parts and tank coatings. Polymers tend to swell and to improve their sealing abiUty when in contact with aromatics, but degree of swell is a function of both elastomer-type and aromatic molecular weight. Rubbers can also be attacked by peroxides that form in fuels that are not properly inhibited (see Elastomers, synthetic Rubber, natural). 

Nitrile (Buna-N) is a rubber compound popular in most household plumbing applications. It s a basic plumbers o-ring seal, and handles most household liquids and chemicals. Because industry pumps so much water, this elastomer may be the single most popular o-ring seeondary seal in the world. Its service range is from -30° F to +250° F (-34° C. to +120 C). 

Let s consider an industrial boiler. You may need at least three of these previous mentioned o-rings just to prevent leaks and drips in a simple hydronie or steam boiler. Raw water comes into the boiler room with pipes, gauges, valves and instrumentation. All these fittings would probably use Nitrile rubber o-ring seals to give long-term leak free service. 

Hard Vacuum Use a balanced o-ring seal for industrial vacuum. For absolute pressure less than 1 kpa (1 kilopascal) use a torsion balanced seal. (Must verify this measurement)... 

Care must be taken in the assembly of the buffered shaft end seals, particularly in the area of the secondary o-ring seals. A cut or damaged ring can allow more oil to be bypassed than from a damaged main seal. 

In contrast to many other surface analytical techniques, like e. g. scanning electron microscopy, AFM does not require vacuum. Therefore, it can be operated under ambient conditions which enables direct observation of processes at solid-gas and solid-liquid interfaces. The latter can be accomplished by means of a liquid cell which is schematically shown in Fig. 5.6. The cell is formed by the sample at the bottom, a glass cover - holding the cantilever - at the top, and a silicone o-ring seal between. Studies with such a liquid cell can also be performed under potential control which opens up valuable opportunities for electrochemistry [5.11, 5.12]. Moreover, imaging under liquids opens up the possibility to protect sensitive surfaces by in-situ preparation and imaging under an inert fluid [5.13]. 

A center barrel supported by the main bearings and consisting of piped or trapezoidal filtrate passages. The sectors are attached to the barrel through "o" ring sealed coimections in a number equal to the number of disc sectors. 

O-rIng sealing lor positive secondary fluid containment. 

FIGURE 23.1 O-ring seal section how shape factor S can vary in different circumstances. 

A more predictable situation exists for an O-ring seal housed as above when contacted and swollen by a liquid solvent. Generally a small amount of positive swell is beneficial to sealing, and it is believed that many seals would not function for long without some swelling. Excessive swelling, however, weakens the seal and leads to total failure by fracture or extmsion. ... 

FIGURE 23.14 Explosive decompression (ED) damage in a fluoroelastomer O-ring seal section left and miscellaneous samples of a nonfluorinated oil-field elastomer right obtained using pressure vessels such as those shown in Eigure 23.15. 

Z. Fang, S. Peterson, and R. Denton. O-ring seal with lubricant additives for rock bit bearings. Patent GB 2318139, 1998. 

Following our visit to the Schatz Lab, we went back to the drawing board and added the O ring seals to the case. In March 1993, the cases were machined to accept the O rings and we were ready to try again. Another dip in the water container with 200 KPa (30 psig) hydrogen pressure showed that the leaks in the fuel cell test fixture had been stopped. 

Figure 2.39 (a) Schematic representation of the experimental arrangement for attenuated total reflection of infrared radiation in an electrochemical cell, (b) Schematic representation of the ATR cell design commonly employed in in situ 1R ATR experiments. SS = stainless steel cell body, usually coated with teflon P — Ge or Si prism WE = working electrode, evaporated or sputtered onto prism CE = platinum counter electrode RE = reference electrode T = teflon or viton O ring seals E = electrolyte. 

A wax-like polymer with resistance to a wide range of temperatures, high resistance to chemical attack and very low frictional resistance. It is widely used in O-rings, seals and gaskets it may also be sintered on to a mould surface to assist the release of the product. Polythene... 

Figure 11.1 (a) Scheme of an isoperibol titration calorimetry apparatus A Dewar vessel B lid C stirrer D electrical resistance E thermistor F titrant delivery tube G O-ring seal, (b) Vessel for isothermal operation A stainless-steel, platinum, or tantalum cup B water-tight stainless steel container C heater D Peltier thermoelectric cooler E O-ring seal F heater and cooler leads. Adapted from [211],... 

A lateral variation of the anodization current will produce different growth rates and consequently an interface roughness for porous layers. Note that this is not the case for stable macro PS formation on n-type, because here the growth rate is independent of current density. An inhomogeneous current distribution at the O-ring seal of an anodization cell or at masked substrates produces PS layer thickness variations, as shown in Fig. 6.6. Inhomogeneities of the current distribution become more pronounced for low doped substrates, as shown in Figs. 6.3 b and 6.5 d [Kr3]. 

O-ring seals are installed around each of the punches to provide a liquid tight seal between the fiberglass shipping tube and the punch clamps. 

XRD Characterization The powder x-ray diffraction of the mechano-chemically milled complex borohydride has been carried out by the Philips X pert diffractometer with Cu-Koi radiation of X= 5.4060 A. The incident and diffraction slit width used for the measurements are 1° and 2° respectively. The sample holder was covered with Polyethylene tape (foil) with an O-ring seal in an N2 filled glove box in order to avoid or at least minimize the 02/moisture pickup during the XRD measurements. The diffraction from the tape was calibrated without the actual sample and found to be occurring at 29 angles of 22° and 24°, respectively. The XRD phase identification and particle size calculation has been carried out using PANalytical X pert Highscore software, version l.Of. 

---