Number of factors

The selection of equipment for the treatment of solid particle emissions to the atmosphere depends on a number of factors ... 

Fig. 3.24 shows the cost breakdown of a typical development well. As can be seen, drilling operations are the area with the largest scope for cost savings. The actual costs of a well show considerable variations and are dependent on a number of factors, e.g. ... 

For each step of the process a number of factors must be considered ... 

Quality in NDT depends upon a number of factors. Qualification of NDT personnel, technical state and correctness of choice of testing equipment, availability of approved working procedures of examination, calibration of NDT equipment have decisive importance among those factors of an NDT laboratory. Assessment of NDT laboratory competence is provided through accreditation in compliance with the EN 45000 series standards. 

The ion time of flight, as given by equation (B1.7.7), is oversimplified, however. There are a number of factors which change the final measured TOP. These are considered below. 

In order to obtain an improved yield of the desired product, an excess over the proportion required by the chemical equation of one (or more) of the reactants is often used. In a given preparation, the selection of the reagent to be employed in excess will depend upon a number of factors these include its relative cost and ease of removal after the reaction, and... 

The mobility of the proton in position 2 of a quaternized molecule and the kinetics of exchange with deuterium has been studied extensively (18-20) it is increased in a basic medium (21-23). The rate of exchange is close to that obtained with the base itself, and the protonated form is supposed to be the active intermediate (236, 664). The remarkable lability of 2-H has been ascribed to a number of factors, including a possible stabilizing resonance effect with contributions of both carbene and ylid structure. This latter may result from the interaction of a d orbital at the sulfur atom with the cr orbital out of the ring at C-2 (21). 

The computation just outlined is easily extended to any number of factors. For a system with three factors, for example, a 2 factorial design can be used to determine the parameters for the empirical model described by the following equation... 

The fuels Hsted in Table 2 are generally representative of fuels to be encountered over the range of industrial furnaces and, depending on the type (cooled or refractory wall), exhibit operating temperatures considerably different from adiabatic values. The choice of fuel is dependent upon a number of factors including cost, availabiUty, cleanliness, emissions, reflabiUty, and operations. Small furnaces tend to bum cleaner, easier to use fuels. Large furnaces can more effectively use coal. 

Although ASTM specifies certain quaUty levels, there are a number of factors that contribute to other quaUty levels in the marketplace. At times, government regulations are more restrictive than ASTM specifications, especiaHy with respect to environmental issues. Secondly, competitive forces may encourage companies to provide fuel quaUty that is better than that defined by ASTM. Thirdly, ASTM specifications do not have the force of law, and certain companies may decide to exceed or not meet their recommended values. In response to this last factor, some states have adopted ASTM fuel quahty specifications as state regulations, thus forcing a minimum quaUty level in the field. 

The Optimum level of gasoline octane is a complex function of a number of factors involving the customer as well as the automotive and petroleum... 

These processes tend to produce Hquids that are higher priced than those derived from cmde oil. Timing for commercialization depends on a number of factors, including price of cmde oil, need for energy self-sufficiency, and environmental considerations. The factors are different for each of the potential sources. Environmental considerations include polution from burning the fuel itself, poUution from the whole production cycle, and production of gases that are involved in the enhanced greenhouse effect (see Air pollution). 

Exact design criteria on equipment for handling acetylene is not readily available because of the great number of factors involved. However, recommendations have been made concerning the equipment, piping, compressors, flash arresters, and proper materials (69,92—94). 

Module Selection. The choice of the appropriate membrane module for a particular membrane separation balances a number of factors. The principal factors that enter into this decision are Hsted in Table 2. 

Because ozone formation occurs only within these microdischarge channels, ozone-production efficiency for the most part depends on the strength of the microdischarges, which is influenced by a number of factors such as the gap width, pressure, properties of the dielectric and metal electrode, power... 

The seam closure on a folding carton is typicahy made using a latex, poly(vinyl acetate), vinyl acetate copolymer, or hot-melt adhesive (27). The choice of adhesive depends on a number of factors, including the nature of any coating used on the package and the production speeds required. 

The protection of a trade secret is a complex task dependent upon any number of factors. The mere formation of an intention to maintain information as secret is not enough actual safeguards must be put into place. The owner of a trade secret must identify the information as a trade secret and protect the information from disclosure. Means used to prevent disclosure might include the following ... 

The position of the equiUbrium depends on a number of factors, such as concentration of siloxane units and the nature of substituents on the sihcon, but is independent of the starting siloxane composition and the polymerization conditions (81,82). For a hulk polymerization of dimethyl siloxane, the equihbrium concentration of cycHc oligomers is approximately 18 wt % (83). The equiHbrium mixture of cyclosiloxanes is composed of a continuous population to at least but D, D, and make over 95 wt % of the total cycHc fraction (84). 

---