Molybdenum tungsten oxides

The existence of at least nine phases in the molybdenum-oxygen system is well established. Their crystal structures are briefly described and it is shown that they can be classified into four main families dependent on whether they possess a basic structure of rutile type, ReOs type, or MoOs type, or have complex structures where polygonal networks can be distinguished. The known tungsten and mixed molybdenum tungsten oxides fit into this scheme. Because of their complicated formulas many of these compounds may be termed "nonstoichiometric," but variance in composition has not been observed for any of them. 

There are no indications that the molybdenum oxides considered exhibit variations of lattice dimensions which would indicate extended homogeneity ranges. They form well developed crystals which give excellent x-ray photographs and they are stable in air up to about 200° C. The crystal structures of all of them have now been studied. They often possess a basic structure, which provides a basis for classification. Such a classification is illustrated in Table II here the known tungsten and mixed molybdenum-tungsten oxides have also been listed, since they fit naturally into such a scheme. 

Bismuth chromate is described by Salter (1869) under bismuth yellow. Bismuth vanadate, in combination with bismuth-molybdenum-tungsten oxides, are known as yellow pigments of modem introduction (Buxbaum, 1998 see bismuth vanadate). 

Some metals used as metallic coatings are considered nontoxic, such as aluminum, magnesium, iron, tin, indium, molybdenum, tungsten, titanium, tantalum, niobium, bismuth, and the precious metals such as gold, platinum, rhodium, and palladium. However, some of the most important poUutants are metallic contaminants of these metals. Metals that can be bioconcentrated to harmful levels, especially in predators at the top of the food chain, such as mercury, cadmium, and lead are especially problematic. Other metals such as silver, copper, nickel, zinc, and chromium in the hexavalent oxidation state are highly toxic to aquatic Hfe (37,57—60). 

HDPE resias are produced ia industry with several classes of catalysts, ie, catalysts based on chromium oxides (Phillips), catalysts utilising organochromium compounds, catalysts based on titanium or vanadium compounds (Ziegler), and metallocene catalysts (33—35). A large number of additional catalysts have been developed by utilising transition metals such as scandium, cobalt, nickel, niobium, molybdenum, tungsten, palladium, rhodium, mthenium, lanthanides, and actinides (33—35) none of these, however, are commercially significant. 

The predominant process for manufacture of aniline is the catalytic reduction of nitroben2ene [98-95-3] ixh. hydrogen. The reduction is carried out in the vapor phase (50—55) or Hquid phase (56—60). A fixed-bed reactor is commonly used for the vapor-phase process and the reactor is operated under pressure. A number of catalysts have been cited and include copper, copper on siHca, copper oxide, sulfides of nickel, molybdenum, tungsten, and palladium—vanadium on alumina or Htbium—aluminum spinels. Catalysts cited for the Hquid-phase processes include nickel, copper or cobalt supported on a suitable inert carrier, and palladium or platinum or their mixtures supported on carbon. 

EBHP is mixed with a catalyst solution and fed to a horizontal compartmentalized reactor where propylene is introduced into each compartment. The reactor operates at 95—130°C and 2500—4000 kPa (360—580 psi) for 1—2 h, and 5—7 mol propylene/1 mol EBHP are used for a 95—99% conversion of EBHP and a 92—96% selectivity to propylene oxide. The homogeneous catalyst is made from molybdenum, tungsten, or titanium and an organic acid, such as acetate, naphthenate, stearate, etc (170,173). Heterogeneous catalysts consist of titanium oxides on a siUca support (174—176). 

The second type of behaviour (Fig. 1.89) is much closer to that which one might predict from the regular cracking of successive oxide layers, i.e. the rate decreases to a constant value. Often the oxide-metal volume ratio (Table 1.27) is much greater than unity, and oxidation occurs by oxygen transport in the continuous oxide in some examples the data can be fitted by the paralinear rate law, which is considered later. Destructive oxidation of this type is shown by many metals such as molybdenum, tungsten and tantalum which would otherwise have excellent properties for use at high temperatures. 

Dithiol is a less selective reagent than thiocyanate for molybdenum. Tungsten interferes most seriously but does not do so in the presence of tartaric acid or citric acid (see Section 17.34). Tin does not interfere if the absorbance is read at 680 nm. Strong oxidants oxidise the reagent iron(III) salts should be reduced with potassium iodide solution and the liberated iodine removed with thiosulphate. 

New inorganic electrode films based on molybdenum and tungsten oxides have been introduced for aqueous solutions heteropolyanion electrodes... 

Fig. 6.1b) in which twelve inner ligands bridge the edges of the Me octahedron, and six outer ligands occupy apical positions, predominate. These units are found in reduced zirconium, niobium, tantalum, and rare-earth halides, and niobium, tantalum, molybdenum and tungsten oxides [la, 6, 10]. 

In the temperature range of400 to 700 °C the values of the equilibrium constants of the first two reactions are larger than the corresponding values for tungsten oxide reduction. Thus, for an equal moisture content in the hydrogen used, the reduction of molybdenum... 

In the case of molten salts, the functional electrolytes are generally oxides or halides. As examples of the use of oxides, mention may be made of the electrowinning processes for aluminum, tantalum, molybdenum, tungsten, and some of the rare earth metals. The appropriate oxides, dissolved in halide melts, act as the sources of the respective metals intended to be deposited cathodically. Halides are used as functional electrolytes for almost all other metals. In principle, all halides can be used, but in practice only fluorides and chlorides are used. Bromides and iodides are thermally unstable and are relatively expensive. Fluorides are ideally suited because of their stability and low volatility, their drawbacks pertain to the difficulty in obtaining them in forms free from oxygenated ions, and to their poor solubility in water. It is a truism that aqueous solubility makes the post-electrolysis separation of the electrodeposit from the electrolyte easy because the electrolyte can be leached away. The drawback associated with fluorides due to their poor solubility can, to a large extent, be overcome by using double fluorides instead of simple fluorides. Chlorides are widely used in electrodeposition because they are readily available in a pure form and... 

Thomas, R., Moulijn, J.A., Debeer, V.H.J. and Medema, J. (1980) Structure-metathesis-activity relations of silica supported molybdenum and tungsten-oxide. J. Mol. Catal., 8, 161. 

Iodide ion-selective electrode The iodide electrode has broad application both in the direct determination of iodide ions present in various media as well as for the determination of iodide in various compounds. It is, for example, important in the determination of iodide in milk [44,64,218, 382, 442], This electrode responds to Hg ions [150, 306, 439] and can be used for the indirect determination of oxidizing agents that react with iodide, such as 10 [305], lOi [158], Pd(II) [117, 347,405] and for the determination of the overall oxidant content, for example in the atmosphere [393], It can also be used to monitor the iodide concentration formed during the reactions of iodide with hydrogen peroxide or perborate, catalyzed by molybdenum, tungsten or vanadium ions, permitting determination of traces of these metals [12,192,193, 194, 195]. The permeability of bilayer lipid membranes for iodide can be measured using an I"... 

The use of /r-hydroxo or ju-alkoxo bridged polynuclear complexes of chromium, molybdenum, tungsten, or rhenium in this route leads to the formation of monomeric bis(NHC) complexes, to the elimination of hydrogen, and to the partial oxidation of the metal [Eq.(ll)]. Chelating and nonchelating imidazolium salts as well as benzimidazolium and tetrazolium salts can be used. 

Molybdenum In its pure form, without additions, it is the most efficient catalyst of all the easily obtainable and reducible substances, and it is less easily poisoned than iron. It catalyzes in another way than iron, insofar as it forms analytically easily detectable amounts of metal nitrides (about 9% nitrogen content) during its catalytic action, whereas iron does not form, under synthesis conditions, analytically detectable quantities of a nitride. In this respect, molybdenum resembles tungsten, manganese and uranium which all form nitrides during their operation, as ammonia catalysts. Molybdenum is clearly promoted by nickel, cobalt and iron, but not by oxides such as alumina. Alkali metals can act favorably on molybdenum, but oxides of the alkali metals are harmful. Efficiency, as pure molybdenum, 1.5%, promoted up to 4% ammonia. 

Reaction with amorphous silicon at 900°C, catalyzed by steam produces cadmium orthosilicate, Cd2Si04. The same product also is obtained by reaction with sdica. Finely divided oxide reacts with dimethyl sulfate forming cadmium sulfate. Cadmium oxide, upon rapid heating with oxides of many other metals, such as iron, molybdenum, tungsten, titanium, tantalum, niobium, antimony, and arsenic, forms mixed oxides. For example, rapid heating with ferric oxide at 750°C produces cadmium ferrite, CdFe204 ... 

Ti02 nanotubes were used to support M0O3 observing a spontaneous dispersion of molybdenum-oxide on the surface of nanotubes, which was different from that observed on titania particles.Supporting tungsten oxides a preferential orientation of the (002) planes was observed. Vanadium-oxide in the form of nanorods could be prepared using the titania nanotube as structure-directing template under hydrothermal... 

Two different kinds of metals are found in chondrites. Small nuggets composed of highly refractory siderophile elements (iridium, osmium, ruthenium, molybdenum, tungsten, rhenium) occur within CAIs. These refractory alloys are predicted to condense at temperatures above 1600 from a gas of solar composition. Except for tungsten, they are also the expected residues of CAI oxidation. 

Clearly, U is the biggest number in the cycle and is the main driving force for the formation of ionic compounds. Nevertheless, the other factors can tip the balance one way or another. For example, AHSub is particularly large for the transition metals niobium, tantalum, molybdenum, tungsten, and rhenium, with the result that, in their lower oxidation states, they do not form simple ionic compounds such as ReCl3 but rather form compounds that contain clusters of bonded metal atoms (in this example, Re3 clusters are involved, so the formula is better written ResClg). 

Write the electron configurations of the chromium, molybdenum, tungsten, and uranium atoms. Why are the sizes of molybdenum and tungsten atoms almost the same Which oxidation states are exhibited by the most stable compounds of these elements (for example, their natural compounds) Explain the observed laws. 

---