Molten salt physical properties

Molten Organic Salts—Physical Properties TABLE I. Total Entropies of Transition d 3... 

Other techniques include oxidative, steam atmosphere (33), and molten salt (34) pyrolyses. In a partial-air atmosphere, mbber pyrolysis is an exothermic reaction. The reaction rate and ratio of pyrolytic filler to ok products are controlled by the oxygen flow rate. Pyrolysis in a steam atmosphere gives a cleaner char with a greater surface area than char pyroly2ed in an inert atmosphere however, the physical properties of the cured compounded mbber are inferior. Because of the greater surface area, this pyrolytic filler could be used as activated carbon, but production costs are prohibitive. Molten salt baths produce pyroly2ed char and ok products from tine chips. The product characteristics and quantities depend on the salt used. Recovery of char from the molten salt is difficult. 

Titanium Silicides. The titanium—silicon system includes Ti Si, Ti Si, TiSi, and TiSi (154). Physical properties are summarized in Table 18. Direct synthesis by heating the elements in vacuo or in a protective atmosphere is possible. In the latter case, it is convenient to use titanium hydride instead of titanium metal. Other preparative methods include high temperature electrolysis of molten salt baths containing titanium dioxide and alkalifluorosiUcate (155) reaction of TiCl, SiCl, and H2 at ca 1150°C, using appropriate reactant quantities for both TiSi and TiSi2 (156) and, for Ti Si, reaction between titanium dioxide and calcium siUcide at ca 1200°C, followed by dissolution of excess lime and calcium siUcate in acetic acid. 

The presence of several anions in these ionic liquids has the effect of significantly decreasing the melting point. Considering that the formation of eutectic mixtures of molten salts is widely used to obtain lower melting points, it is surprising that little effort has been put into identifying the effects of mixtures of cations or anions on the physical properties of other ionic liquids [17]. 

The field of reaction chemistry in ionic liquids was initially confined to the use of chloroaluminate(III) ionic liquids. With the development of neutral ionic liquids in the mid-1990s, the range of reactions that can be performed has expanded rapidly. In this chapter, reactions in both chloroaluminate(III) ionic liquids and in similar Lewis acidic media are described. In addition, stoichiometric reactions, mostly in neutral ionic liquids, are discussed. Review articles by several authors are available, including Welton [1] (reaction chemistry in ionic liquids), Holbrey [2] (properties and phase behavior), Earle [3] (reaction chemistry in ionic liquids), Pagni [4] (reaction chemistry in molten salts), Rooney [5] (physical properties of ionic liquids), Seddon [6, 7] (chloroaluminate(III) ionic liquids and industrial applications), Wasserscheid [8] (catalysis in ionic liquids), Dupont [9] (catalysis in ionic liquids) and Sheldon [10] (catalysis in ionic liquids). 

Molten salt investigation methods can be divided into two classes thermodynamic and kinetic. In some cases, the analysis of melting diagrams and isotherms of physical-chemical properties such as density, surface tension, viscosity and electroconductivity enables the determination of the ionic composition of the melt. Direct investigation of the complex structure is performed using spectral methods [294]. 

G. J. Janz, J. Phys. Chem. Ref Data 17, Supplement (1988) Thermodynamic and Transport Properties for Molten Salts Correlation Equations for Critically Evaluated Density, Surface Tension, Eleetrieal Conduetance and Viseosity Data, American Chemical Society-American Institute of Physics-National Bureau of Standards, Washington, DC, 1988. 

G J. Janz, C. B. Allen, N. P. Bansal, R. M. Murphy, and R. P. T. Tomkins, Physical Properties Data Compilations Relevant to Energy Storage, Molten Salts Data on Single and Multi-Component Salt Systems, U.S. Dept, of Commerce, National Bureau of Standards, NBS-NSRDS-61, Washington, DC, 1979. 

Phase Equilibria and Physical Properties of Chloroaluminate Molten Salts. 277... 

Relatively little attention has been devoted to the direct electrodeposition of transition metal-aluminum alloys in spite of the fact that isothermal electrodeposition leads to coatings with very uniform composition and structure and that the deposition current gives a direct measure of the deposition rate. Unfortunately, neither aluminum nor its alloys can be electrodeposited from aqueous solutions because hydrogen is evolved before aluminum is plated. Thus, it is necessary to employ nonaqueous solvents (both molecular and ionic) for this purpose. Among the solvents that have been used successfully to electrodeposit aluminum and its transition metal alloys are the chloroaluminate molten salts, which consist of inorganic or organic chloride salts combined with anhydrous aluminum chloride. An introduction to the chemical, electrochemical, and physical properties of the most commonly used chloroaluminate melts is given below. 

Although chemically similar, the inorganic and organic chloroaluminate molten salts or ionic liquids, as some prefer to call them, differ greatly with respect to their melting temperatures and physical properties. Figures 1 and 2 show the phase diagrams... 

A novel application of ionic liquids in biochemistry involved duplex DNA as the anion and polyether-decorated transition metal complexes. When the undiluted liquid DNA-or molten salt-is interrogated electrochemically by a microelectrode, the molten salts exhibit cyclic voltammograms due to the physical diffusion (D-PHYS) of the polyether-transition metal complex. These DNA molten salts constitute a new class of materials whose properties can be controlled by nucleic acid sequence and that can be interrogated in undiluted form on microelectrode arrays (Leone et al., 2001). 

Metallic State. The actinide metals, like the lanthanide metals, are highly electropositive. They can be prepared by the electrolysis of molten salts or by the reduction of a halide with an electropositive metal, such as calcium or barium. Their physical properties are summarized in Table 3. 

Molten carbonates are of interest because of their applications as electrolytes in molten salt fuel cells. The preparation, handling, physical and electrochemical properties, and important applications of molten alkali carbonates have been described at length [4,5], Li2C03, Na2C03, and K2C03 and various mixtures of these salts are the carbonates most frequently used as electrochemical solvents. The major impurities in alkali carbonates are alkali hydroxides and oxides produced through hydrolysis and dissociation ... 

Comprehensive reviews describing the preparation, purification, and physical and electrochemical properties of these melts have been published [17-20]. The most popular systems are mixtures of A1C13 with either l-(l-butyl)pyridinium chloride (BupyCl) or 1 -methyl-3-ethylimidazolium chloride (MeEtimCl). These systems are very versatile solvents for electrochemistry because they are stable over a wide temperature range. In many ways they can be considered to be a link between conventional nonaqueous solvent/supporting electrolyte systems and conventional high-temperature molten salts. 

---