Molecular block copolymers

The first case concerns particles with polymer chains attached to their surfaces. This can be done using chemically (end-)grafted chains, as is often done in the study of model colloids. Alternatively, a block copolymer can be used, of which one of the blocks (the anchor group) adsorbs strongly to the particles. The polymer chains may vary from short alkane chains to high molecular weight polymers (see also section C2.6.2). The interactions between such... 

Amide interchange reactions of the type represented by reaction 3 in Table 5.4 are known to occur more slowly than direct amidation nevertheless, reactions between high and low molecular weight polyamides result in a polymer of intermediate molecular weight. The polymer is initially a block copolymer of the two starting materials, but randomization is eventually produced. 

A brief review has appeared covering the use of metal-free initiators in living anionic polymerizations of acrylates and a comparison with Du Font s group-transfer polymerization method (149). Tetrabutylammonium thiolates mn room temperature polymerizations to quantitative conversions yielding polymers of narrow molecular weight distributions in dipolar aprotic solvents. Block copolymers are accessible through sequential monomer additions (149—151) and interfacial polymerizations (152,153). 

G-5—G-9 Aromatic Modified Aliphatic Petroleum Resins. Compatibihty with base polymers is an essential aspect of hydrocarbon resins in whatever appHcation they are used. As an example, piperylene—2-methyl-2-butene based resins are substantially inadequate in enhancing the tack of 1,3-butadiene—styrene based random and block copolymers in pressure sensitive adhesive appHcations. The copolymerization of a-methylstyrene with piperylenes effectively enhances the tack properties of styrene—butadiene copolymers and styrene—isoprene copolymers in adhesive appHcations (40,41). Introduction of aromaticity into hydrocarbon resins serves to increase the solubiHty parameter of resins, resulting in improved compatibiHty with base polymers. However, the nature of the aromatic monomer also serves as a handle for molecular weight and softening point control. 

Styrenic block copolymers (SBCs) are also widely used in HMA and PSA appHcations. Most hot melt appHed pressure sensitive adhesives are based on triblock copolymers consisting of SIS or SBS combinations (S = styrene, I = isoprene B = butadiene). Pressure sensitive adhesives typically employ low styrene, high molecular weight SIS polymers while hot melt adhesives usually use higher styrene, lower molecular weight SBCs. Resins compatible with the mid-block of an SBC improves tack properties those compatible with the end blocks control melt viscosity and temperature performance. 

Polymerization ofiVIasked Disilenes. A novel approach, namely, the anionic polymerization of masked disilenes, has been used to synthesize a number of poly(dialkylsilanes) as well as the first dialkylamino substituted polysilanes (eq. 13) (111,112). The route is capable of providing monodisperse polymers with relatively high molecular weight M = lO" — 10 ), and holds promise of being a good method for the synthesis of alternating and block copolymers. 

Polymerization of methacrylates is also possible via what is known as group-transfer polymerization. Although only limited commercial use has been made of this technique, it does provide a route to block copolymers that is not available from ordinary free-radical polymerizations. In a prototypical group-transfer polymerization the fluoride-ion-catalyzed reaction of a methacrylate (or acrylate) in the presence of a silyl ketene acetal gives a high molecular weight polymer (45—50). 

Among the techniques employed to estimate the average molecular weight distribution of polymers are end-group analysis, dilute solution viscosity, reduction in vapor pressure, ebuUiometry, cryoscopy, vapor pressure osmometry, fractionation, hplc, phase distribution chromatography, field flow fractionation, and gel-permeation chromatography (gpc). For routine analysis of SBR polymers, gpc is widely accepted. Table 1 lists a number of physical properties of SBR (random) compared to natural mbber, solution polybutadiene, and SB block copolymer. 

Styrene—butadiene block copolymers are made with anionic chain carriers, and low molecular weight PS is made by a cationic mechanism (110). Analytical standards are available for PS prepared by all four mechanisms (see Initiators). 

Step-Growth Gopolymerization. A sample of a block copolymer prepared by condensation polymerisation is shown in equation 30 (37). In this process, a prepolymer diol (HO—Z—OH) is capped with isocyanate end groups and chain extended with a low molecular-weight diol (HO—E—OH) to give a so-called segmented block copolymer, containing polyurethane hard blocks and O—Z—O soft blocks. 

Whereas random copolymers exhibit one T described by equation 38, block copolymers, because of this microphase separation, exhibit two glass-transition temperatures. The T of each block is close to, if not the same as, the homopolymer from which it was formed. Polymer properties are also affected by the arrangement of the blocks. This is shown for high styrene-containing or high molecular-weight styrene resias of various block arrangements ia Table 3. 

The molecular stmcture of the copolymers is also important. Molecular-weight measurements (osmometry, gpc) and functional group analysis are useful. Block copolymers require supermolecular (morphological) stmctural information as well. A listing of typical copolymer characterization tools and methods is shown in Table 6. 

As shown in the previous section the mechanical and thermal properties of polypropylene are dependent on the isotacticity, the molecular weight and on other structure features. The properties of five commercial materials (all made by the same manufacturer and subjected to the same test methods) which are of approximately the same isotactic content but which differ in molecular weight and in being either homopolymers or block copolymers are compared in Table 11.1. 

A wide range of polyether-polyamide block copolymers were first offered by Atochem in 1981 under the trade name Pebax. These are made by first producing a low molecular weight polyamide using an excess of dicarboxylic acid at a temperature above 230°C and under a pressure of up to 25 bar. This is then combined with a polyether by reaction at 230-280°C under vacuum (O.l-lOTorr) in the presence of a suitable catalyst such as Ti(OR)4. 

With a typical of 25 000-30000 the molecular size is low compared wjth most conventional covalently cross-linked elastomers. With such rubbers values of about 100000 are desirable so that the effects of a significant amount of non-load-bearing chain ends do not occur. Such a problem does not arise in block copolymers terminated by hard segments. 

---