Misnomers

The name D.D.T. is derived from dichlorodiphenylfrichloroethane this is a misnomer since the name represents 27 different compounds. As commonly employed it refers to 2 2-6ts(p-chlorophenyl)-l 1 1-trichloroethane. It is conveniently prepared by the condensation of chlorobenzene and chloral hydrate in the presence of concentrated sulphuric acid ... 

The initiators which are used in addition polymerizations are sometimes called catalysts, although strictly speaking this is a misnomer. A true catalyst is recoverable at the end of the reaction, chemically unchanged. Tliis is not true of the initiator molecules in addition polymerizations. Monomer and polymer are the initial and final states of the polymerization process, and these govern the thermodynamics of the reaction the nature and concentration of the intermediates in the process, on the other hand, determine the rate. This makes initiator and catalyst synonyms for the same material The former term stresses the effect of the reagent on the intermediate, and the latter its effect on the rate. The term catalyst is particularly common in the language of ionic polymerizations, but this terminology should not obscure the importance of the initiation step in the overall polymerization mechanism. 

Renewable carbon resources is a misnomer the earth s carbon is in a perpetual state of flux. Carbon is not consumed such that it is no longer available in any form. Reversible and irreversible chemical reactions occur in such a manner that the carbon cycle makes all forms of carbon, including fossil resources, renewable. It is simply a matter of time that makes one carbon from more renewable than another. If it is presumed that replacement does in fact occur, natural processes eventually will replenish depleted petroleum or natural gas deposits in several million years. Eixed carbon-containing materials that renew themselves often enough to make them continuously available in large quantities are needed to maintain and supplement energy suppHes biomass is a principal source of such carbon. 

Gas Combustion Retort. The continuous gas combustion retort (GCR) has been modeled after the earlier batch-operation NTU retort. Although the term "gas combustion" has been appHed to this process, it is a misnomer in that, in a weU-designed and properly operated system, the residual char on the retorted shale suppHes much of the fuel for this process. The GCR is the foremnner of most continuous AGR processes (Table 7). 

Physical Properties. Trichloromethanesulfenyl chloride [594-42-3] (perchloromethyl mercaptan, a misnomer but used as the common commercial name), CCl SCl, is a strongly acrid, pale yellow Hquid, boiling at 149°C with some decomposition at atmospheric pressure, 68°C at 6.93 kPa (52... 

Physical Properties. Sodium metabisulfite (sodium pyrosulfite, sodium bisulfite (a misnomer)), Na2S20, is a white granular or powdered salt (specific gravity 1.48) and is storable when kept dry and protected from air. In the presence of traces of water it develops an odor of sulfur dioxide and in moist air it decomposes with loss of part of its SO2 content and by oxidation to sodium sulfate. Dry sodium metabisulfite is more stable to oxidation than dry sodium sulfite. At low temperatures, sodium metabisulfite forms hydrates with 6 and 7 moles of water. The solubiHty of sodium metabisulfite in water is 39.5 wt % at 20°C, 41.6 wt % at 40°C, and 44.6 wt % at 60°C (340). Sodium metabisulfite is fairly soluble in glycerol and slightly soluble in alcohol. 

Spent acid burning is actually a misnomer, for such acids are decomposed to SO2 and H2O at high temperatures in an endothermic reaction. Excess water in the acid is also vaporized. Acid decomposition and water vaporization require considerable heat. Any organic compounds present in the spent acid oxidize to produce some of the required heat. To supply the additional heat required, auxiUary fuels, eg, oil or gas, must be burned. When available, sulfur and H2S are excellent auxiUary fuels. 

Filtration. Filtration is usually a misnomer for tertiary processes that remove particulate matter. Small particles are removed by adsorption rather than by physical straining. If secondary effluents contain a high concentration of soHds, filter beds clog and binding occurs at the bed surface. 

The demand for metallic arsenic is limited and thus arsenic is usually marketed in the form of the trioxide, referred to as white arsenic, arsenious oxide, arsenious acid anhydride, and also by the generally accepted misnomer arsenic. 

The term tar sands is a misnomer tar is a product of coal processing. Oil sands is also a misnomer but equivalent to usage of "oil shale." Bituminous sands is more correct bitumen is a naturally occurring asphalt. Asphalt is a product of a refinery operation, usually made from a residuum. Residuum is the nonvolatile portion of petroleum and often further defined as atmospheric (bp > 350° C) or vacuum (bp > 565° C). For convenience, the terms "asphalt" and "bitumen" will be used interchangeably in this article. 

Some pump eompanies will design replaceable wear bands for the OD of the impeller eye and the bore of the pump housing. It s said that the pump loses 1.5% to 2% efficiency points for every one thousandths wear in a wear band beyond the factory setting. Therefore, by changing wear bands, the pump is returned to its original effieiency. Becau.se of this, the term wear band is a misnomer. A better term would be effieiency band (Figure 6-19). 

Particulate fillers are divided into two types, inert fillers and reinforcing fillers. The term inert filler is something of a misnomer as many properties may be affected by incorporation of such a filler. For example, in a plasticised PVC compound the addition of an inert filler will reduce die swell on extrusion, increase modulus and hardness, may provide a white base for colouring, improve electrical insulation properties and reduce tackiness. Inert fillers will also usually substantially reduce the cost of the compound. Amongst the fillers used are calcium carbonates, china clay, talc, and barium sulphate. For normal uses such fillers should be quite insoluble in any liquids with which the polymer compound is liable to come into contact. 

Historically, this phenomenon was referred to as unconfined vapor cloud explosion, but, in general, the term unconfined is a misnomer. It is more accurate to call this type of explosion simply a vapor cloud explosion. ... 

HLW comprises most of the radioactivity associated with nuclear waste. Because that designation can cover radioactive waste from more than one source, the term spent nuclear fuel (SNF) will be used to discuss HLW originating from commercial nuclear reactors. LLW comprises nearly 90 percent of the volume of nuclear waste but little of the radioactivity. Nuclear power reactors produce SNF and most of the nation s LLW, although there are approximately 20,000 different sources of LLW. The name SNF is a bit of a misnomer because it implies that there is no useful material left in the fuel, when in fact some fissionable material is left in it. 

E. Photoelectric photometer method (Section 17.6). In this method the human eye is replaced by a suitable photoelectric cell the latter is employed to afford a direct measure of the light intensity, and hence of the absorption. Instruments incorporating photoelectric cells measure the light absorption and not the colour of the substance for this reason the term photoelectric colorimeters is a misnomer better names are photoelectric comparators, photometers, or, best, absorptiometers. 

NOTE Simple HW heating and LP steam boiler treatment apart, the term BW treatment is unfortunately often something of a misnomer. The practice is, in fact, generally recognized to be primarily concerned with adjustments to the boiler FW chemistry and the addition of polishing chemicals to compensate for deficiencies or potential problems associated with the FW rather than with the recirculating BW. 

A typical buffering agent used in shampoo is sodium citrate. Since the goal is to keep the shampoo slightly acid, the term pH balanced is actually a misnomer. You actually want the balance to be tipped slightly to the acidic side. 

Histopathological features are dominated by the large number of centrally-placed muscle nuclei, sometimes affecting more than 90% of muscle fibers. The nuclei form long chains in the middle of the fiber and are surrounded by cytoplasm, which contains mitochondria and membranous vesicles, but no myofibrils. This morphological appearance has prompted comparison with myotubes, and in fact centronuclear myopathies are sometimes referred to as myotubular myopathies. This is a misnomer, however, since although the affected fibers retain some of the structural features of myotubes, and maturational arrest may play a role in their formation, the vast majority of such fibers are fully differentiated histochemically into either type 1 or type 2. 

However, despite this misnomer, when interest in the closed-tube flame of the Ellis-type resurfaced in the mid-1980s, the researchers involved were also aware of the DDT tulips and the name transferred to the cusped laminar flame transition [11-14]. An example of a flame image from this era is shown in Figure 5.3.4, and the "tulip" name is now used routinely to... 

Dental silicate cement was also variously known in the past as a translucent, porcelain or vitreous cement. The present name is to some extent a misnomer, probably attached to the cement in the mistaken belief that it was a silicate cement, whereas we now know that it is a phosphate-bonded cement. It is formed by mixing an aluminosilicate glass with an aqueous solution of orthophosphoric acid. After preparation the cement paste sets within a few minutes in the mouth. It is, perhaps, the strongest of the purely inorganic cements when prepared by conventional methods, with a compressive strength that can reach 300 MPa after 24 hours (Wilson et al, 1972). 

While the terms amperometric detection and coulometric detection have come into use to describe detectors of less than 100% efficiency and 100% efficiency respectively, these terms are actually misnomers. An amperometric detector is any electrochemical detector where current is plotted as a function of time, regardless of the conversion efficiency. A coulometric detector is any electrochemical detector where charge is plotted as a function of time, again regardless of the conversion efficiency. Preferred terminology should be high efficiency and low efficiency detectors to describe the two situations. 

---