Metre

The field unit for permeability is the Darcy (D) or millidarcy (mD). For clastic oil reservoirs, a good permeability would be greater than 0.1 D (100 mD), while a poor permeability would be less than 0.01 D (10 mD). For practical purposes, the millidarcy is commonly used (1 mD = 10" m ). For gas reservoirs 1 mD would be a reasonable permeability because the viscosity of gas is much lower than that of oil, this permeability would yield an acceptable flowrate for the same pressure gradient. Typical fluid velocities in the reservoir are less than one metre per day. 

Steel piled jackets are the most common type of platform and are employed in a wide range of sea conditions, from the comparative calm of the South China Sea to the hostile Northern North Sea. Steel jackets are used in water depths of up to 150 metres and may support production facilities a further 50 metres above mean sea level. In deep water all the process and support facilities are normally supported on a single jacket, but in shallow seas it may be cheaper and safer to support drilling, production... 

Material Veloeity. Defines the velocity, in metres/sec, of ultrasound in the material of the test piece used to convert A-scan signal time to distances within the test piece. 

Intersections of butts and seams of fabrication and section welds Throughout hull envelope, longitudinal and transverse bulkheads, inner bottom and hopper bottom The summation of checkpoint lengths (see note 2) examined at intersections is to be L where L is the overall length of the ship in metres... 

The methodology and the pigging tool have proven to be capable of identifying very small leaks. In oil pipelines like the Danish carrying 1500 m /h leakages down to 1 litre per hour can be detected without injection of large quantities of tracer. Leakages can be positioned with an accuracy of less than 1 metre. 

A microelectrode is an electrode with at least one dimension small enough that its properties are a fimction of size, typically with at least one dimension smaller than 50 pm [28, 29, 30, 31, 32 and 33]. If compared with electrodes employed in industrial-scale electrosynthesis or in laboratory-scale synthesis, where the characteristic dimensions can be of the order of metres and centimetres, respectively, or electrodes for voltannnetry with millimetre dimension, it is clear that the size of the electrodes can vary dramatically. This enonnous difference in size gives microelectrodes their unique properties of increased rate of mass transport, faster response and decreased reliance on the presence of a conducting medium. Over the past 15 years, microelectrodes have made a tremendous impact in electrochemistry. They have, for example, been used to improve the sensitivity of ASV in enviroiunental analysis, to investigate rapid... 

In the microwave region tunable monochromatic radiation is produced by klystrons, each one being tunable over a relatively small frequency range, or a backward wave oscillator, tunable over a much larger range. Both are electronic devices. Absorption experiments are usually carried out in the gas phase, and mica windows, which transmit in this region, are placed on either end of the absorption cell, which may be several metres in length. Stark... 

Dimensions are physical quantities such as mass (M), length (L), and time (T) and examples of units corresponding to these dimensions are the gram (g), metre (m) and second (s). If, for example, something has a mass of 3.5 g then we write... 

The te.st is carried out by using an apparatus shown in Figure 11.8, consisting of a closed test chamber in which talcum powder can pass through a sieve having square openings of 75 fim, and is held in suspension by an air current. The amount of talcum powder is supplied at 2 kg per cubic metre size of the test chamber. The enclosure under lest is placed inside the chamber and is connected to a vacuum pump which maintains, inside the enclosure, a differential pressure equivalent to not more than a 200 mm eolumn of water. 

The sizes of cables considered above refer to normal operating conditions and a distance of around 10/15 metres between the starter and the... 

The ambient temperature should be measured during the last quarter of the test by at least three thermometers or thermocouples placed equally around the switchgear assembly, at almost the centre level and at about I metre from the body of the enclosure. The ambient temperature to be considered must be the average of these readings and should be within 10-40°C. To ensure that the ambient temperature is unaffected by ntagnetic field, alcohol thermometers must be used and not mercury thermometers. 

Note Cable junction b has a high refraction and reflection. Arrester would be essential to protect the cable rather than the transformer, if 2Vi > BIL of the cable. If the cable is long enough say. > 50 metre or so, the natural dampening of Ihe incident wave up to junction b may be enough and may not cause any harmful effect even without the arrester... 

If / is the distatice in metres from the arrester terminals to the equipment, then... 

A = area of cross-section of core in square metres k = total length of the magnetic circuit in metres... 

---