Metal complexes thermodynamic stability

Marin, D. Mendicuti, F. Polarographic Determination of Composition and Thermodynamic Stability Constant of a Complex Metal Ion, /. Chem. Educ. 1988, 65, 916-918. 

The factors leading to the high resistance of the noble metals to chemical attack, i.e. their thermodynamic stability over a wide range of conditions and the possibility of the formation of very thin protective films under oxidising conditions, have already been mentioned. A factor tending to reduce corrosion resistance in aqueous solutions is the tendency of these metals to form complexes with some anions. 

Compared to the sum of covalent radii, metal-silicon single bonds are significantly shortened. This phenomenon is explained by a partial multiple bonding between the metal and silicon [62]. A comparison of several metal complexes throughout the periodic table shows that the largest effects occur with the heaviest metals. However, conclusions drawn concerning the thermodynamic stability of the respective M —Si bonds should be considered with some reservation [146], since in most cases the compared metals show neither the same coordination geometries nor the same oxidation states. 

The first thing to point out is that the use of a pentafluorophenyl CgFs group with late transition metal confers on the complexes great stability, both thermodynamic and kinetic. This general fact, that is also true in gold chemistry, can be explained by different factors ... 

The above account of selectivity of inorganic plus organic chemistry in synthesis is given rather extensively to stress three points. All the four (Mg, Fe, Co and Ni) porphyrin products came from one source, the synthesis of uroporphyrin. The basis of selection is very different from that in primitive centres which use thermodynamic stability constant selectivity based on different donor atoms for different metal ions. Here, all ion complexes have the same donor atoms, nitrogen, the most constrained being the coordination of Mg2+ by five nitrogens exactly as is seen for Fe in haemoglobin. Hence, there also has to be a new control feedback to ensure that the appropriate quantities of each metal cofactor is produced in a balanced way, that is synthesis from uroporphyrin has to be divided based upon... 

Electroless deposition should not be confused with metal displacement reactions, which are often known as cementation or immersion plating processes. In the latter, the less noble metal dissolves and eventually becomes coated with a more noble metal, and the deposition process ceases. Coating thicknesses are usually < 1 pm, and tend to be less continuous than coatings obtained by other methods. A well-known example of an immersion plating process that has technological applications is the deposition of Sn on Cu [17] here a strong complexant for Cu(I), such as thiourea, forces the Cu(I)/Cu couple cathodic with respect to the Sn(II)/Sn couple, thereby increasing the thermodynamic stability in solution of thiourea-complexed Cu(I) relative to Sn(II). 

Borrok et al. (2004a) used potentiometric titration to measure Cd sorption by different bacterial consortia, and a surface complexation approach to determine thermodynamic stability constants. When the data were modeled by adopting a single set of stability constants, a similar sorption behavior was shown by a wide range of bacterial species. Further, current models that rely on pure strains of laboratory-cultivated bacterial species appear to overestimate the extent of metal biosorption in natural systems. 

In general, the cryptands (213) show a stronger correlation between thermodynamic stability and match of the metal ion for the cavity. Thermodynamic data for complexation of the alkali metal ions with a number of cryptands is summarized in Table 6.2. The data for the smaller (less flexible) cryptands 2.1.1, 2.2.1, and 2.2.2 illustrate well the occurrence of peak selectivity. 

Thermodynamic Stability (log of Selected Mn11 Complexes and Their Comparison with Other Biogenic Metal Ions at 298 K... 

The thermodynamic stability of a complex ML formed from an acceptor metal ion M and ligand groups L may be approached in two different but related ways. (The difference between the two approaches lies in the way in which the formation reaction is presented.) Consistent with preceding sections, an equilibrium constant may be written for the formation reaction. This is the formation constant Kv In a simple approach, the effects of the solvent and ionic charges may be ignored. A stepwise representation of the reaction enables a series of stepwise formation constants to be written (Table 3.5). 

---