Mechanisms epoxidation

Dihydroxyiation of epoxides can be carried out with syn stereospecificity using OSO4 as the active oxidant. The reaction occurs by a cycioaddition mechanism. Epoxidation is aiso a stereospecific syn addition. Ring opening of epoxides by hydroiysis aiso ieads to diois. This is usuaiiy an anf/addition with inversion of configuration at the site of nucieophiiic attack, ieading to overaii anf/dihydroxyiation. 

Apart from acrylate-based systems, which are cured by a free-radical mechanism, epoxide-based systems that are cured cationically are also used. Epoxide-based formulations yield excellent overprint varnishes on tin-free steel and aluminum for rigid packaging, especially when producing steel food cans and aluminum beer and... 

The same disconnection can be used with simple epoxides when the sulphur ylid (A) is used a reagent for the synthon CH2. Draw a mechanism for the reaetion ... 

The reaction mixture in ethyl acetate is then transferred to a 100-ml reactor, purged under a nitrogen atmosphere, 340 mg of Lil is added, and the whole mass is then heated, with mechanical stirring, on an oil bath, up to ethyl acetate reflux temperature. The heating is continued for 5 hours, until the disappearance of the epoxide (II), as evidenced by the thin-layer chromatography. 

The mechanism of alkene epoxidation is believed to be a concerted process mvolv mg a single bimolecular elementary step as shown m Figure 6 14... 

These monomers provide a means for introducing carboxyl groups into copolymers. In copolymers these acids can improve adhesion properties, improve freeze-thaw and mechanical stability of polymer dispersions, provide stability in alkalies (including ammonia), increase resistance to attack by oils, and provide reactive centers for cross-linking by divalent metal ions, diamines, or epoxides. 

The tert-huty hydroperoxide is then mixed with a catalyst solution to react with propylene. Some TBHP decomposes to TBA during this process step. The catalyst is typically an organometaHic that is soluble in the reaction mixture. The metal can be tungsten, vanadium, or molybdenum. Molybdenum complexes with naphthenates or carboxylates provide the best combination of selectivity and reactivity. Catalyst concentrations of 200—500 ppm in a solution of 55% TBHP and 45% TBA are typically used when water content is less than 0.5 wt %. The homogeneous metal catalyst must be removed from solution for disposal or recycle (137,157). Although heterogeneous catalysts can be employed, elution of some of the metal, particularly molybdenum, from the support surface occurs (158). References 159 and 160 discuss possible mechanisms for the catalytic epoxidation of olefins by hydroperoxides. 

Work in the mid-1970s demonstrated that the vitamin K-dependent step in prothrombin synthesis was the conversion of glutamyl residues to y-carboxyglutamyl residues. Subsequent studies more cleady defined the role of vitamin K in this conversion and have led to the current theory that the vitamin K-dependent carboxylation reaction is essentially a two-step process which first involves generation of a carbanion at the y-position of the glutamyl (Gla) residue. This event is coupled with the epoxidation of the reduced form of vitamin K and in a subsequent step, the carbanion is carboxylated (77—80). Studies have provided thermochemical confirmation for the mechanism of vitamin K and have shown the oxidation of vitamin KH2 (15) can produce a base of sufficient strength to deprotonate the y-position of the glutamate (81—83). 

Physical and Chemical Properties. The (F)- and (Z)-isomers of cinnamaldehyde are both known. (F)-Cinnamaldehyde [14371-10-9] is generally produced commercially and its properties are given in Table 2. Cinnamaldehyde undergoes reactions that are typical of an a,P-unsaturated aromatic aldehyde. Slow oxidation to cinnamic acid is observed upon exposure to air. This process can be accelerated in the presence of transition-metal catalysts such as cobalt acetate (28). Under more vigorous conditions with either nitric or chromic acid, cleavage at the double bond occurs to afford benzoic acid. Epoxidation of cinnamaldehyde via a conjugate addition mechanism is observed upon treatment with a salt of /-butyl hydroperoxide (29). 

Mechanisms for polymerization of epoxides by Lewis acids are proposed in References 11—15. 

Mechanisms for reaction of tertiary amines with epoxides are discussed in References 16 and 17. 

The reactions are highly exothermic. Under Uquid-phase conditions at about 200°C, the overall heat of reaction is —83.7 to —104.6 kJ/mol (—20 to —25 kcal/mol) ethylene oxide reacting (324). The opening of the oxide ring is considered to occur by an ionic mechanism with a nucleophilic attack on one of the epoxide carbon atoms (325). Both acidic and basic catalysts accelerate the reactions, as does elevated temperature. The reaction kinetics and product distribution have been studied by a number of workers (326,327). 

Transition metal-catalyzed epoxidations, by peracids or peroxides, are complex and diverse in their reaction mechanisms (Section 5.05.4.2.2) (77MI50300). However, most advantageous conversions are possible using metal complexes. The use of t-butyl hydroperoxide with titanium tetraisopropoxide in the presence of tartrates gave asymmetric epoxides of 90-95% optical purity (80JA5974). 

CRV737) A critical discussion of the mechanisms of ring-opening of epoxides by nucleophiles. 

Oxaziridines are generally formed by the action of a peracid on a combination of a carbonyl compound and an amine, either as a Schiff base (243) or a simple mixture. Yields are between 65 and 90%. Although oxygenation of Schiff bases is formally analogous to epoxidation of alkenes, the true mechanism is still under discussion. More favored than an epoxidation-type mechanism is formation of a condensation product (244), from which an acyloxy group is displaced with formation of an O—N bond. 

Because of their favourable price, polyesters are preferred to epoxide and furane resins for general purpose laminates and account for at least 95% of the low-pressure laminates produced. The epoxide resins find specialised uses for chemical, electrical and heat-resistant applications and for optimum mechanical properties. The furane resins have a limited use in chemical plant. The use of high-pressure laminates from phenolic, aminoplastic and silicone resins is discussed elsewhere in this book. 

As indicated in the preceding section, amine hardeners will cross-link epoxide resins either by a catalytic mechanism or by bridging across epoxy molecules. In general the primary and secondary amines act as reactive hardeners whilst the tertiary amines are catalytic. 

Compared with the polyesters the epoxide resins generally have better mechanical properties and, using appropriate hardeners, better heat resistance and chemical resistance, in particular, resistance to alkalis. 

---