Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Matrix polyamide

The influence of external variables, i.e. testing and environmental conditions such as rate of loading, temperature and moisture, on fracture mechanisms and hence on fracture toughness in short fibre polymer composites is investigated as a function of fibre orientation with respect to the fracture plane. Unidirectionally oriented materials with different polymer matrix (polyamide 6.6 and polyoxymethylene) and different glass fibre content (15wt% and 30wt%) are examined. [Pg.387]

SEM photomicrograph (magnification lOOOx) of cryofracture surfaces showing the absence of adhesion in melt-blended 70 wt% polyamide 6/15 wt% polystyrene/15 wt% polypropylene ternary blend. All the visible particles are detached from the matrix of polyamide 6 as an indication of absence of interfacial adhesion between the minor phases (PS, PP) and the host matrix polyamide 6. (From T. S. Omonov, Crucial Aspects of Phase Morphology Generation and Stabilization in Two- and Three-Phase Polymer Blends Physical, Reactive and Combined Routes of Compatibilization, Ph.D. thesis, Katholieke Universiteit Leuven, Belgium, 200 under the supervision of C. Harrats and G. Groeninckx.)... [Pg.24]

Minor phase impact modifier Matrix polyamide 66... [Pg.275]

Minor phase polymeric modifier Matrix polyamide 6... [Pg.276]

Minor phase brominated polystyrene Matrix polyamide 66 glass fiber reinforced... [Pg.285]

Fig. 2. Ultrafine fibers are produced by spinning bicomponent or biconstituent polymer mixtures, highly stretching such products to ultrafine deniers, and extracting or otherwise removing the undesked matrix carrier to release the desked ultrafine fibers (30). For example, spinning polyester islands in a matrix of polystyrene and then, after stretching, dissolving the polystyrene to leave the polyester fibers cospinning polyester with polyamides, then stretching,... Fig. 2. Ultrafine fibers are produced by spinning bicomponent or biconstituent polymer mixtures, highly stretching such products to ultrafine deniers, and extracting or otherwise removing the undesked matrix carrier to release the desked ultrafine fibers (30). For example, spinning polyester islands in a matrix of polystyrene and then, after stretching, dissolving the polystyrene to leave the polyester fibers cospinning polyester with polyamides, then stretching,...
The thermoplastic or thermoset nature of the resin in the colorant—resin matrix is also important. For thermoplastics, the polymerisation reaction is completed, the materials are processed at or close to their melting points, and scrap may be reground and remolded, eg, polyethylene, propjiene, poly(vinyl chloride), acetal resins (qv), acryhcs, ABS, nylons, ceUulosics, and polystyrene (see Olefin polymers Vinyl polymers Acrylic ester polymers Polyamides Cellulose ESTERS Styrene polymers). In the case of thermoset resins, the chemical reaction is only partially complete when the colorants are added and is concluded when the resin is molded. The result is a nonmeltable cross-linked resin that caimot be reworked, eg, epoxy resins (qv), urea—formaldehyde, melamine—formaldehyde, phenoHcs, and thermoset polyesters (qv) (see Amino resins and plastics Phenolic resins). [Pg.456]

Whilst the aliphatic nylons are generally classified as being impact resistant, they are affected by stress concentrators like sharp comers which may lead to brittle failures. Incorporation of mbbers which are not soluble in the nylons and hence form dispersions of rubber droplets in the polyamide matrix but which nevertheless can have some interaction between mbber and polyamide can be most effective. Materials described in the literature include the ethylene-propylene rubbers, ionomers (q.v.), polyurethanes, acrylates and methacrylates, ABS polymers and polyamides from dimer acid. [Pg.498]

The matrix is usually polypropylene and it is this which melts during processing to permit shaping of the material. The rubber filler particles then contribute the flexibility and resilience to the material. The other type of TPR is the polyamide and the properties of all five types are summarised in Table 1.4. [Pg.11]

The behavior of the physico-mechanical characteristics of polymeric composites is easily traceable in the table given in [144] which presents the results of experiments with polyamide matrices filled with resite particles of different shape. The filler concentrations were adjusted so that the integral contact surface area in the filler-matrix system remained the same. [Pg.18]

Clays have long been used as fillers in polymer systems because of low cost and the improved mechanical properties of the resulting polymer composites. If all other parameters are equal, the efficiency of a filler to improve the physical and mechanical properties of a polymer system is sensitive to its degree of dispersion in the polymer matrix (Krishnamoorti et ah, 1996). In the early 1990s, Toyota researchers (Okada et ah, 1990) discovered that treatment of montmorillonite (MMT) with amino acids allowed dispersion of the individual 1 nm thick silicate layers of the clay scale in polyamide on a molecular. Their hybrid material showed major improvements in physical and mechanical properties even at very low clay content (1.6 vol %). Since then, many researchers have performed investigations in the new field of polymer nano-composites. This has lead to further developments in the range of materials and synthesizing methods available. [Pg.29]

One of the few disadvantages associated with nanoparticle incorporation concerns the loss of some properties. Some of the data presented have suggested that nanoclay modification of polymers such as polyamide could reduce impact performance [28]. Nanofillers are sometimes very matrix-specific. High cost of nanofillers prohibits their use. [Pg.34]

Although the interest in, and application of layer chromatography has historically resulted from the development of PC, it was soon replaced by thin-layer chromatography (TLC). In PC, only one stationary phase matrix is available (cellulose), at variance to TLC (silica, polyamide, ion-exchange resins, cellulose). Using a silica-gel plate, separation of a sample can be accomplished in approximately 1 h as compared with many hours on paper. The plate size is much smaller than the necessary paper size. Also, more samples can be spotted... [Pg.218]

A few other successful 13C 1-NMR determinations should be mentioned. Hunt et al. [28] used 13C NMR to characterise fractions of extracted analytes of PAG and sorbitan ester samples and identified Irganox 1010. H and 13C NMR have been used to identify the main organic components of a breathable diaper back-sheet as LLDPE and pentaerythritol tetra-octyl ester (PETO) [233]. The equally present AOs Irganox 1010 and Irgafos 168 were not detected without extraction. Barendswaard et al. [234] have reported fully assigned 13C solution spectra of these two antioxidants. Chimas-sorb 944 in a polyamide matrix can be determined by H or 13C 1-NMR using solvents such as formic acid, trifluoroacetic acid or trifluoroethanol [235], Both H and 13C NMR have been used to follow the chemistry of a bis-phenoxidemethylaluminum complex (reaction product of BHT and trimethylaluminum) by exposure in air. Pierre and van Bree [216] also used 13C NMR to... [Pg.334]

The use of ionisation techniques such as El and Cl for TLC stationary phases has generally been limited to relatively nonpolar and thermally stable molecules. Polar involatile compounds, separated on silica gel, generally strongly adsorb on to the matrix, and decompose when heat is applied for volatilisation [817]. Use of less-adsorbent phases, such as polyamide, is particularly useful for TLC-EIMS work, because the analytes are not as strongly adsorbed to this phase and do not require high probe temperatures [818,819]. For compounds that are not suitable candidates for TLC-EIMS, FAB can be employed. Chemical ionisation, although suitable for TLC-MS, appears to have been little used. [Pg.539]

In spite of the high polarity of PA6, identification of additives was also feasible in formulations of PA6/additive dissolutions, although with decreased sensitivity. Hostavin N 20, Irganox B 1171, Tinuvin 320 and Tinuvin 350 can be determined in PA6 in technical concentrations, although the sensitivity is less than for nonpolar polymers, such as polyolefins. This was tentatively explained as follows. In a nonpolar polymer matrix, the electronically excited polar additive molecule can easily be desorbed. In the polar polyamide matrix, desorption of the additives is hindered by strong polar interactions (e.g. hydrogen bridges) between the excited analytes and the polymer matrix. This hinders selective desorption of the additives by laser irradiation. However, in a polymer/additive matrix-modified solution, evaporated to dryness, the interactions between the polar... [Pg.708]


See other pages where Matrix polyamide is mentioned: [Pg.388]    [Pg.63]    [Pg.276]    [Pg.343]    [Pg.91]    [Pg.92]    [Pg.388]    [Pg.63]    [Pg.276]    [Pg.343]    [Pg.91]    [Pg.92]    [Pg.693]    [Pg.150]    [Pg.301]    [Pg.309]    [Pg.463]    [Pg.117]    [Pg.20]    [Pg.505]    [Pg.151]    [Pg.418]    [Pg.46]    [Pg.669]    [Pg.671]    [Pg.86]    [Pg.112]    [Pg.363]    [Pg.383]    [Pg.860]    [Pg.278]    [Pg.9]    [Pg.42]    [Pg.273]    [Pg.7]    [Pg.544]    [Pg.172]    [Pg.65]    [Pg.80]   
See also in sourсe #XX -- [ Pg.66 , Pg.401 , Pg.408 ]




SEARCH



Matrix polymers polyamide

Matrix resin polyamide

© 2024 chempedia.info