Materials voltammetry

In voltammetry we measure the current in an electrochemical cell as a function of the applied potential. Individual voltammetric methods differ in terms of the type of electrode used, how the applied potential is changed, and whether the transport of material to the electrode s surface is enhanced by stirring. 

Pretreatment of the collected particulate matter may be required for chemical analysis. Pretreatment generally involves extraction of the particulate matter into a liquid. The solution may be further treated to transform the material into a form suitable for analysis. Trace metals may be determined by atomic absorption spectroscopy (AA), emission spectroscopy, polarogra-phy, and anodic stripping voltammetry. Analysis of anions is possible by colorimetric techniques and ion chromatography. Sulfate (S04 ), sulfite (SO-, ), nitrate (NO3 ), chloride Cl ), and fluoride (F ) may be determined by ion chromatography (15). 

Electrical methods of analysis (apart from electrogravimetry referred to above) involve the measurement of current, voltage or resistance in relation to the concentration of a certain species in solution. Techniques which can be included under this general heading are (i) voltammetry (measurement of current at a micro-electrode at a specified voltage) (ii) coulometry (measurement of current and time needed to complete an electrochemical reaction or to generate sufficient material to react completely with a specified reagent) (iii) potentiometry (measurement of the potential of an electrode in equilibrium with an ion to be determined) (iv) conductimetry (measurement of the electrical conductivity of a solution). 

Successful electrodeposition of Sb2To3 has been reported for the first time by Leimkiihler et al. [229] who prepared polycrystalline thin films of the material on different transparent conductive oxides, as well as CdTe and Mo, from uncomplexed solutions made by mixing stock solutions of SbCb, Te02, and phthalate buffer (pH 4). The electrochemical process was discussed in detail based on results obtained by cyclic voltammetry on ITO/glass. The bath temperature was found to influence... 

Sodium formate serves as a reducing reagent for aldehyde in subcrit-ical water at 310-350°C and high pressures (Eq. 8.10).31 The reduction of aldehydes in aqueous media can also be achieved by using an electrochemical method. The voltammetry of benzaldehyde in an acidic methanol/water mixture is affected strongly by the cathode material.30... 

Fig. 5.19 Electrodes used in voltammetry. A—dropping mercury electrode (DME). R denotes the reservoir filled with mercury and connected by a plastic tube to the glass capillary at the tip of which the mercury drop is formed. B—ultramicroelectrode (UME). The actual electrode is the microdisk at the tip of a Wollaston wire (a material often used for UME) sealed in the glass tube...

On the basis of theoretical calculations Chance et al. [203] have interpreted electrochemical measurements using a scheme similar to that of MacDiarmid et al. [181] and Wnek [169] in which the first oxidation peak seen in cyclic voltammetry (at approx. + 0.2 V vs. SCE) represents the oxidation of the leucoemeraldine (1 A)x form of the polymer to produce an increasing number of quinoid repeat units, with the eventual formation of the (1 A-2S")x/2 polyemeraldine form by the end of the first cyclic voltammetric peak. The second peak (attributed by Kobayashi to degradation of the material) is attributed to the conversion of the (1 A-2S")x/2 form to the pernigraniline form (2A)X and the cathodic peaks to the reverse processes. The first process involves only electron transfer, whereas the second also involves the loss of protons and thus might be expected to show pH dependence (whereas the first should not), and this is apparently the case. Thus the second peak would represent the production of the diprotonated (2S )X form at low pH and the (2A)X form at higher pH with these two forms effectively in equilibrium mediated by the H+ concentration. This model is in conflict with the results of Kobayashi et al. [196] who found pH dependence of the position of the first peak. 

Polythiophene films can be electrochemically cycled from the neutral to the conducting state with coulombic efficiencies in excess of 95% [443], with little evidence of decomposition of the material up to + 1.4 V vs. SCE in acetonitrile [37, 54, 56, 396,400] (the 3-methyl derivative being particularly stable [396]), but unlike polypyrrole, polythiophene can be both p- and n-doped, although the n-doped material has a lower maximum conductivity [444], Cyclic voltammetry shows two sets of peaks corresponding to the p- and n-doping reactions, with E° values at approximately + 1.1 V and — 1.4 V respectively (vs. an Ag+/Ag reference electrode)... 

---