Low-Density Polyethylene High-Pressure Process

Dieter Uttmann, Giulia Mei, Diego Mauricio Castaneda-Zuniga, Christian-Ulrich Schmidt, and Cerd Mannebach 

Low-density polyethylene (LDPE) is the oldest commercially available polyethylene resin that was first discovered by ICI in 1933 during screening experiments on various chemicals that apply high-pressure conditions. By compressing ethylene to 1400 bars in the presence of benzaldehyde and traces of oxygen, a white solid was formed that proved to be LDPE. In 1936, ICI obtained a patent (Gibson et al., GB 471590) for the chemical polymerization process whose nature is of a free radical type. 

LDPE attained rapid popularity due to its electrical insulating properties, which were exploited for the development of radar technology during the Second World War. After the discovery of LD PE s excellent film forming properties in the late 1940s, a sudden increase in demand took place, which triggered the worldwide commercialization of the resin and related technologies. 

---

Theonly important current application of tubular reactors in polymer syntheses is in the production of high pressure, low density polyethylene. In tubular processes, the newer reactors typically have inside diameters about 2.5 cm and lengths of the order of I km. Ethylene, a free-radical initiator, and a chain transfer agent are injected at the tube inlet and sometimes downstream as well. The high heat of polymerization causes nonisothermal conditions with the temperature increasing towards the tube center and away from the inlet. A typical axial temperature profile peaks some distance down the tube where the bulk of the initiator has been consumed. The reactors are operated at 200-300°C and 2000-3000 atm pressure. 

The second type of solution polymerization concept uses mixtures of supercritical ethylene and molten PE as the medium for ethylene polymerization. Some reactors previously used for free-radical ethylene polymerization in supercritical ethylene at high pressure (see Olefin POLYMERS,LOW DENSITY polyethylene) were converted for the catalytic synthesis of LLDPE. Both stirred and tubular autoclaves operating at 30—200 MPa (4,500—30,000 psig) and 170—350°C can also be used for this purpose. Residence times in these reactors are short, from 1 to 5 minutes. Three types of catalysts are used in these processes. The first type includes pseudo-homogeneous Ziegler catalysts. In this case, all catalyst components are introduced into a reactor as hquids or solutions but form soHd catalysts when combined in the reactor. Examples of such catalysts include titanium tetrachloride as well as its mixtures with vanadium oxytrichloride and a trialkyl aluminum compound (53,54). The second type of catalysts are soHd Ziegler catalysts (55). Both of these catalysts produce compositionaHy nonuniform LLDPE resins. Exxon Chemical Company uses a third type of catalysts, metallocene catalysts, in a similar solution process to produce uniformly branched ethylene copolymers with 1-butene and 1-hexene called Exact resins (56). 

Low density polyethylene produced by a high-pressure high-temperature reaction process. This creates a molecule with a high degree of random branching. Thus crystallinity and hence density are low. 

In some processes, a diluent, like benzene or chlorobenzene are used as the solvent. At high pressure and temperature, both the polyethylene and the monomers dissolve in these solvents so that the reaction occur in a solution phase. In a typical process, 10-30 per cent of the monomer is converted to polymer per cycle. Rest of monomer is recycled. Extensive chain transfer reactions take place during polymerisation to yield a branched polyethylene. Apart from long branches it is also having a large number of short branches of unto 5 carbon atoms formed by intramolecular chain transfer reactions. A typical molecule of Low density polyethylene is having a short branch for about every 50 carbon atoms and one or two long branches per molecule. 

Coordination copolymerization of ethylene with small amounts of an a-olefin such as 1-butene, 1-hexene, or 1-octene results in the equivalent of the branched, low-density polyethylene produced by radical polymerization. The polyethylene, referred to as linear low-density polyethylene (LLDPE), has controlled amounts of ethyl, n-butyl, and n-hexyl branches, respectively. Copolymerization with propene, 4-methyl-1-pentene, and cycloalk-enes is also practiced. There was little effort to commercialize linear low-density polyethylene (LLDPE) until 1978, when gas-phase technology made the economics of the process very competitive with the high-pressure radical polymerization process [James, 1986]. The expansion of this technology was rapid. The utility of the LLDPE process Emits the need to build new high-pressure plants. New capacity for LDPE has usually involved new plants for the low-pressure gas-phase process, which allows the production of HDPE and LLDPE as well as polypropene. The production of LLDPE in the United States in 2001 was about 8 billion pounds, the same as the production of LDPE. Overall, HDPE and LLDPE, produced by coordination polymerization, comprise two-thirds of all polyethylenes. 

Some particular processes can require very high pressures for special applications (i.e. in explosive welding and plating), but pressures between 100 and 1000 bar can be found easily in different industrial processes. Typical examples are the synthesis of ammonia, the synthesis of methanol and the production of low-density polyethylene, but also analytical techniques as high-pressure liquid chromatography. Other important implications are for the storage and transportation of fluids and enhanced oil recovery. 

Many industrially important chemical processes are high pressure processes. Examples are the production of ammonia and the production of low density polyethylene. Basically, the pressure affects both the equilibrium yield of a chemical reaction and the reaction rate. Here, only the influence on the equilibrium yield is discussed. 

The first section of this chapter describes the most important high pressure process run under homogeneous conditions to manufacture Low Density PolyEthylene (LDPE). The radical polymerization of ethylene to LDPE is carried out in tubular reactors or in stirred autoclaves. Tubular reactors exhibit higher capacities than stirred autoclaves. The latter are preferred to produce ethylene copolymers having a higher comonomer content. 

As in any other process, so also in the high-pressure polymerization of ethylene, do capital costs, utilities, maintenance, manpower, and costs of raw materials contribute to the production costs of low-density polyethylene (LDPE). The cost structure is typical for the production of bulk chemicals but is strongly influenced by the requirements of a high-pressure process. 

In many cases, the linear low-density polyethylene (LLDPE) produced in low-pressure processes competes for the same market as LDPE. For this reason, in Figure 8.2-7 capital- and operation costs of the high-pressure polymerization are compared with those of a low-pressure solution process having the same capacity. Also, the production costs of the low-pressure process are dominated by the costs of the monomer, but some differences can be noted which are typical for the economics of low- and high-pressure processes. 

It is expected that around 500,000 tons mPE will be manufactured in 2000 in Western Europe. Resins from high-pressure- as well as from low-pressure processes suffer more difficult processability. Their narrow molecular-weight distribution results in an unfavourable viscosity behaviour [8], As with linear low-density polyethylene (LLDPE), the viscosity of mPE is independent of the shear-rate over a wide range and reduces only at high shear-rates (Fig. 9.5-11). Therefore, energy consumption is high when mPE is processed with extruders which are designed for LDPE. 

---