Iron product selectivities over

Although acrylonitrile manufacture from propylene and ammonia was first patented in 1949 (30), it was not until 1959, when Sohio developed a catalyst capable of producing acrylonitrile with high selectivity, that commercial manufacture from propylene became economically viable (1). Production improvements over the past 30 years have stemmed largely from development of several generations of increasingly more efficient catalysts. These catalysts are multicomponent mixed metal oxides mostly based on bismuth—molybdenum oxide. Other types of catalysts that have been used commercially are based on iron—antimony oxide, uranium—antimony oxide, and tellurium-molybdenum oxide. 

For IDA, IV iron, though costly, has superior bioavailability compared with oral preparations. In select individuals the bioavailability advantage of parenteral iron over oral iron can be the difference in the achievement of a successful outcome. The benefits of using combination oral iron products designed to enhance absorption is probably not warranted. 

Metallic iron itself has very low FTS activity. Although, under operational conditions the activity of metallic iron gradually increases over time. To improve the FTS activity and tune the product selectivity of iron catalysts, promoters such as alkali metals, transition metals and other additives are incorporated into the catalyst structure. Typical promoters and additives include copper, potassium and silica. Copper acts to enhance the rate of catalyst activation, silica improves the dispersion of catalytically active iron species, while alkali metals aid carbon-monoxide dissociation from surface iron. ... 

In the direct ammoxidation of propane over Fe-zeolite catalysts the product mixture consisted of propene, acrylonitrile (AN), acetonitrile (AcN), and carbon oxides. Traces of methane, ethane, ethene and HCN were also detected with selectivity not exceeding 3%. The catalytic performances of the investigated catalysts are summarized in the Table 1. It must be noted that catalytic activity of MTW and silicalite matrix without iron (Fe concentration is lower than 50 ppm) was negligible. The propane conversion was below 1.5 % and no nitriles were detected. It is clearly seen from the Table 1 that the activity and selectivity of catalysts are influenced not only by the content of iron, but also by the zeolite framework structure. Typically, the Fe-MTW zeolites exhibit higher selectivity to propene (even at higher propane conversion than in the case of Fe-silicalite) and substantially lower selectivity to nitriles (both acrylonitrile and acetonitrile). The Fe-silicalite catalyst exhibits acrylonitrile selectivity 31.5 %, whereas the Fe-MTW catalysts with Fe concentration 1400 and 18900 ppm exhibit, at similar propane conversion, the AN selectivity 19.2 and 15.2 %, respectively. On the other hand, Fe-MTW zeolites exhibit higher AN/AcN ratio in comparison with Fe-silicalite catalyst (see Table 1). Fe-MTW-11500 catalyst reveals rather rare behavior. The concentration of Fe ions in the sample is comparable to Fe-sil-12900 catalyst, as well as... 

The objective of the present study is to develop a cross-flow filtration module operated under low transmembrane pressure drop that can result in high permeate flux, and also to demonstrate the efficient use of such a module to continuously separate wax from ultrafine iron catalyst particles from simulated FTS catalyst/ wax slurry products from an SBCR pilot plant unit. An important goal of this research was to monitor and record cross-flow flux measurements over a longterm time-on-stream (TOS) period (500+ h). Two types (active and passive) of permeate flux maintenance procedures were developed and tested during this study. Depending on the efficiency of different flux maintenance or filter media cleaning procedures employed over the long-term test to stabilize the flux over time, the most efficient procedure can be selected for further development and cost optimization. The effect of mono-olefins and aliphatic alcohols on permeate flux and on the efficiency of the filter membrane for catalyst/wax separation was also studied. 

Anthraquinone is the primary product of the oxidation of anthracene over V2Os-based catalysts. The reaction is very selective and high yields of anthraquinone are possible due to its relatively high stability. An iron vanadate catalyst is used in the industrial process and yields of 80—90 mol. % are reported at 320—370°C. Phthalic anhydride, maleic anhydride and carbon oxides are the by-products. 

---