Ionomer density

Many catalyst layer models have appeared in the literature during the last few years [15, 16, 17, 18, 19,20, 21]. This observation partly explains the complications associated with this topic. Still, much work remains to be completed since many effects have not yet been included, such as proton surface diffusion (outside the ionomer, [22,23]) and ionomer density (water content effect), which effectively and respectively increases/modifies the reactive surface area. The surface-sensitive nature of Pt catalysts on the oxygen reduction reaction rate [24] and electrochemical promotion (a catalytic effect, [25]) represent other examples which can also affect the reaction rate and surface area. All these effects are further compounded by the potential presence of hquid water which effectively modifies the reaction front, access to speeifie eatalyst particles and surface properties. 

The combined effects of a divalent Ca counterion and thermal treatment can be seen from studies of PMMA-based ionomers [16]. In thin films of Ca-salts of this ionomer cast from methylene chloride, and having an ion content of only 0.8 mol%, the only observed deformation was a series of long, localized crazes, similar to those seen in the PMMA homopolymer. When the ionomer samples were subject to an additional heat treatment (8 h at 100°C), the induced crazes were shorter in length and shear deformation zones were present. This behavior implies that the heat treatment enhanced the formation of ionic aggregates and increased the entanglement strand density. The deformation pattern attained is rather similar to that of Na salts having an ion content of about 6 mol% hence, substitution of divalent Ca for monovalent Na permits comparable deformation modes, including some shear, to be obtained at much lower ion contents. 

The mechanical properties of ionomers are generally superior to those of the homopolymer or copolymer from which the ionomer has been synthesized. This is particularly so when the ion content is near to or above the critical value at which the ionic cluster phase becomes dominant over the multiplet-containing matrix phase. The greater strength and stability of such ionomers is a result of efficient ionic-type crosslinking and an enhanced entanglement strand density. 

This process is highly suitable for rubbers with poor solubility. In this process, the rubber sheet is soaked in TEOS or quite often in TEOS-solvent mixture and the in situ sUica generation is conducted by either acid or base catalysis. The sol-gel reaction is normally carried out at room temperature. Kohjiya et al. [29-31] have reported various nonpolar mbber-silica hybrid nanocomposites based on this technique. The network density of the rubber influences the swelling behavior and hence controls the silica formation. It is very likely that there has been a graded silica concentration from surface to the bulk due to limited swelling of the rubber. This process has been predominantly used to prepare ionomer-inorganic hybrids by Siuzdak et al. [48-50]. 

Ethylene ionomers consist of copolymers of ethylene and an organic add, such as methacrylic acid, the acid moieties of which have been neutralized to form a metal salt. The metal salts from neighboring chains tend to form clusters, such as the one shown schematically in Fig. 18.3. The net result is the overall structure shown in Fig. 18.2 g), in which the ionic clusters form weak crosslinks between adjacent chains. Ionomers also contain short and long chain branches, which are similar to those found in low density polyethylene. 

We make polyethylene resins using two basic types of chain growth reaction free radical polymerization and coordination catalysis. We use free radical polymerization to make low density polyethylene, ethylene-vinyl ester copolymers, and the ethylene-acrylic acid copolymer precursors for ethylene ionomers. We employ coordination catalysts to make high density polyethylene, linear low density polyethylene, and very low density polyethylene. 

LDL receptor (LDLR), 5.T89 L-DOPA, 2 560, 606 LDPE copolymers, 20 213-214. See also Low density polyethylene (LDPE) LDPE film, gels in, 20 229-230 LDPE homopolymer, 20 212 LDPE ionomers, 20 214 LDPE polymerization, peroxide initiators for, 20 218t... 

The experimental optimization of Nafion ionomer loading within a catalyst layer has attracted widespread attention in the fuel cell community, mainly due to its critical role in dictating the reaction sites and mass transport of reactants and products [15,128-134]. Nafion ionomer is a key component in the CL, helping to increase the three-phase reaction sites and platinum utilization to retain moisture, as well as to prevent membrane dehydration, especially at low current densities. Optimal Nafion content in the electrode is necessary to achieve high performance. 

These studies showed that sulfonate groups surrounding the hydronium ion at low X sterically hinder the hydration of fhe hydronium ion. The interfacial structure of sulfonafe pendanfs in fhe membrane was studied by analyzing structural and dynamical parameters such as density of the hydrated polymer radial distribution functions of wafer, ionomers, and protons water coordination numbers of side chains and diffusion coefficients of water and protons. The diffusion coefficienf of wafer agreed well with experimental data for hydronium ions, fhe diffusion coefficienf was found to be 6-10 times smaller than the value for bulk wafer. 

The macrohomogeneous model was exploited in optimization studies of the catalyst layer composition. The theory of composifion-dependent performance reproduces experimental findings very well. - The value of the mass fraction of ionomer that gives the highest voltage efficiency for a CCL with uniform composition depends on the current density range. At intermediate current densities, 0.5 A cm < jo < 1.2 A cm , the best performance is obtained with 35 wt%. The effect of fhe Nation weight fraction on performance predicted by the model is consistent with the experimental trends observed by Passalacqua et al. ... 

Note 1 The mobility of the polymer segments surrounding the multiplets is reduced relative to that of bulk material. With increasing ion content, the number density of the ionomer multiplets increases, leading to overlapping of the restricted mobility regions around the multiplets and the formation of clusters. 

The effects of ionizing radiation on a low and a high density polyethylene and an ionomer indicate that similar networks are formed in the ionomer and in the low density polyethylene. The former crosslinks about 1.5 times as readily as the latter. In the high density resin, the network characteristics, and hence, presumably, the type and distribution of links, differ considerably from those in the other two resins. As a result, crosslinking rates in the high and low density polyethylenes cannot be directly compared. 

Figure 11 shows the variation of modulus with elongation at rupture for these three resins. The results, though scattered, clearly indicate that the ionomer and low density resin follow the same relation. However, a completely different relation is followed by the annealed high... 

In view of the similarity in behavior of the networks in the ionomer and low density resin, we are able to deduce from modulus and elongation at rupture measurements the relative crosslinking rates. It appears that Surlyn A crosslinks 50 to 60% more rapidly than DFD 6040. The increased crosslinking in the ionomer may be associated with the radio-... 

---