Oxide Interference

The terms hot corrosion or dry corrosion are normally taken to apply to the reactions taking place between metals and gases at temperatures above 100 C i.e. temperatures at which the presence of liquid water is unusual. The obvious cases of wet corrosion at temperatures above 100 C, i.e. in pressurised boilers or autoclaves, are not considered here. In practice, of course, common metals and alloys used at temperatures above normal do not suffer appreciable attack in the atmosphere until the temperature is considerably above 100 C. Thus iron and low-alloy steels form only the thinnest of interference oxide films at about 200 C, copper shows the first evidence of tarnishing at about 180 C, and while aluminium forms a thin oxide film at room temperature, the rate of growth is extremely slow even near the melting point. 

Manganese ions interfere (oxidized to permanganate) as do also mercury(II) salts, molybdates, and vanadates, which give blue to violet compounds with the reagent in acid solution. The influence of molybdates can be eliminated by the addition of saturated oxalic acid solution thereby forming the complex H2[Mo03(C204)]. 

The kinetics of reactions in which a new phase is formed may be complicated by the interference of that phase with the ease of access of the reactants to each other. This is the situation in corrosion and tarnishing reactions. Thus in the corrosion of a metal by oxygen the increasingly thick coating of oxide that builds up may offer more and more impedance to the reaction. Typical rate expressions are the logarithmic law,... 

Anodic-stripping voltaimnetry (ASV) is used for the analysis of cations in solution, particularly to detemiine trace heavy metals. It involves pre-concentrating the metals at the electrode surface by reducmg the dissolved metal species in the sample to the zero oxidation state, where they tend to fomi amalgams with Hg. Subsequently, the potential is swept anodically resulting in the dissolution of tire metal species back into solution at their respective fomial potential values. The detemiination step often utilizes a square-wave scan (SWASV), since it increases the rapidity of tlie analysis, avoiding interference from oxygen in solution, and improves the sensitivity. This teclmique has been shown to enable the simultaneous detemiination of four to six trace metals at concentrations down to fractional parts per billion and has found widespread use in seawater analysis. 

Masking by oxidation or reduction of a metal ion to a state which does not react with EDTA is occasionally of value. For example, Fe(III) (log K- y 24.23) in acidic media may be reduced to Fe(II) (log K-yyy = 14.33) by ascorbic acid in this state iron does not interfere in the titration of some trivalent and tetravalent ions in strong acidic medium (pH 0 to 2). Similarly, Hg(II) can be reduced to the metal. In favorable conditions, Cr(III) may be oxidized by alkaline peroxide to chromate which does not complex with EDTA. 

Many samples containing silicon also contain aluminum and iron. After dehydration, these metals are present as AI2O3 and Fe203. These oxides are potential interferents since they also are capable of forming volatile fluorides. 

Both oxidizing and reducing agents can interfere with this analysis. Explain what effect each of these interferents will have on the result of an analysis. 

Explain why strong oxidizing agents interfere with this analysis and why an excess of hydroxylamine prevents such interferences from occurring. 

Minimizing Chemical Interferences The quantitative analysis of some elements is complicated by chemical interferences occurring during atomization. The two most common chemical interferences are the formation of nonvolatile compounds containing the analyte and ionization of the analyte. One example of a chemical interference due to the formation of nonvolatile compounds is observed when P04 or AP+ is added to solutions of Ca +. In one study, for example, adding 100 ppm AP+ to a solution of 5 ppm Ca + decreased the calcium ion s absorbance from 0.50 to 0.14, whereas adding 500 ppm POp to a similar solution of Ca + decreased the absorbance from 0.50 to 0.38. These interferences were attributed to the formation of refractory particles of Ca3(P04)2 and an Al-Ca-O oxide. 

Minimizing Spectral Interferences The most important spectral interference is a continuous source of background emission from the flame or plasma and emission bands from molecular species. This background emission is particularly severe for flames in which the temperature is insufficient to break down refractory compounds, such as oxides and hydroxides. Background corrections for flame emission are made by scanning over the emission line and drawing a baseline (Figure 10.51). Because the temperature of a plasma is... 

Selecting a Constant Potential In controlled-potential coulometry, the potential is selected so that the desired oxidation or reduction reaction goes to completion without interference from redox reactions involving other components of the sample matrix. To see how an appropriate potential for the working electrode is selected, let s develop a constant-potential coulometric method for Cu + based on its reduction to copper metal at a Pt cathode working electrode. 

In controlled-potential coulometry, accuracy is determined by current efficiency and the determination of charge. Provided that no interferents are present that are easier to oxidize or reduce than the analyte, current efficiencies of greater than 99.9% are easily obtained. When interferents are present, however, they can often be eliminated by applying a potential such that the exhaustive electrolysis of the interferents is possible without the simultaneous electrolysis of the analyte. Once the interferents have been removed the potential can be switched to a level at... 

Two methods are used to measure pH electrometric and chemical indicator (1 7). The most common is electrometric and uses the commercial pH meter with a glass electrode. This procedure is based on the measurement of the difference between the pH of an unknown or test solution and that of a standard solution. The instmment measures the emf developed between the glass electrode and a reference electrode of constant potential. The difference in emf when the electrodes are removed from the standard solution and placed in the test solution is converted to a difference in pH. Electrodes based on metal—metal oxides, eg, antimony—antimony oxide (see Antimony AND ANTIMONY ALLOYS Antimony COMPOUNDS), have also found use as pH sensors (8), especially for industrial appHcations where superior mechanical stabiUty is needed (see Sensors). However, because of the presence of the metallic element, these electrodes suffer from interferences by oxidation—reduction systems in the test solution. 

Ferrous Sulfdte Titration. For deterrnination of nitric acid in mixed acid or for nitrates that are free from interferences, ferrous sulfate titration, the nitrometer method, and Devarda s method give excellent results. The deterrnination of nitric acid and nitrates in mixed acid is based on the oxidation of ferrous sulfate [7720-78-7] by nitric acid and may be subject to interference by other materials that reduce nitric acid or oxidize ferrous sulfate. Small amounts of sodium chloride, potassium bromide, or potassium iodide may be tolerated without serious interference, as can nitrous acid up to 50% of the total amount of nitric acid present. Strong oxidizing agents, eg, chlorates, iodates, and bromates, interfere by oxidizing the standardized ferrous sulfate. 

Ozone can be analyzed by titrimetry, direct and colorimetric spectrometry, amperometry, oxidation—reduction potential (ORP), chemiluminescence, calorimetry, thermal conductivity, and isothermal pressure change on decomposition. The last three methods ate not frequently employed. Proper measurement of ozone in water requites an awareness of its reactivity, instabiUty, volatility, and the potential effect of interfering substances. To eliminate interferences, ozone sometimes is sparged out of solution by using an inert gas for analysis in the gas phase or on reabsorption in a clean solution. Historically, the most common analytical procedure has been the iodometric method in which gaseous ozone is absorbed by aqueous KI. 

The hberated iodine is measured spectrometricaHy or titrated with Standard sodium thiosulfate solution (I2 +28203 — 2 1 VS Og following acidification with sulfuric acid buffers are sometimes employed. The method requires measurement of the total gas volume used in the procedure. The presence of other oxidants, such as H2O2 and NO, can interfere with the analysis. The analysis is also technique-sensitive, since it can be affected by a number of variables, including temperature, time, pH, iodide concentration, sampling techniques, etc (140). A detailed procedure is given in Reference 141. 

The ease of hydrolysis of metal alkoxides makes metal analysis a comparatively simple task. In many cases, the metal may be estimated by hydrolysis of a sample in a cmcible, and ignition to the metal oxide. Alternatively, the metal ion may be brought into solution by hydrolysis of a sample with dilute acid, followed by a standard analytical procedure for a solution of that particular metal. If the alcohol Hberated during the hydrolysis is likely to cause interference, it may be distilled from the solution by boiling. 

---