Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Hydrophobic/hydrophilic properties

Hydrophilic/hydrophobic properties. In water-based systems, the filler should be compatible with water because filler dispersion occurs in an aqueous medium before a polymer emulsion is added. In general, most fillers are hydropho-... [Pg.631]

These points, however, do not address the central question of how organisms deal with a contaminated environment with which they have to interact in order to obtain energy and metabolites. Crucial to these processes are the cellular processes which can modify the ionisation of molecules, their hydrophilic/ hydrophobic properties, and the matrix within which they exist. Many of these changes occur in the alimentary tract but they also occur at the cellular... [Pg.391]

Instead, native starch has been oxidized with H202 in the presence of soluble organometallic complexes to meet specific hydrophilic/hydrophobic properties needed for end-products to be used in paper, paint and cosmetic industries [79-... [Pg.68]

Washing and Cleaning Action. The properties of alkyl ether sulfates, due to the good solubility and the special hydrophilic/hydrophobic properties of the molecule, are of particular practical interest. From the investigations described in sections 2 and 3, it can be concluded that, in addition to the decrease in the Krafft Point, favorable properties for practical applications can be expected as a result of the inclusion of the oxyethylene groups into the hydrophobic part of the molecule. As is true for other anionic surfactants, the electrical double layer will be compressed by the addition of multivalent cations. By this means, the adsorption at the interface is increased, the surface activity is raised, and, furthermore, the critical micelle concentration decreased. In the case of the alkyl ether sulfates, however these effects can be obtained without encountering undesirable salting out effects. [Pg.14]

One way of improving the physical and mechanical properties of the polymeric materials produced was to copolymerize the original monomers with stiffer comonomers, whose corresponding homopolymers are endowed with high thermal and mechanical properties. Therefore, 1,4-cyclohexanedimetha-nol was copolymerized with 1,3-propanediol and succinic acid. Segmented copolymers between oligofpropylene succinate)s and PEG were also produced in order to modify their hydrophilic/hydrophobic properties. [Pg.151]

The negative effect that this latter competition has can be limited or even avoided by an adequate choice or tailoring of the molecular sieve hydrophilic/hydrophobic properties. The optimization of the operating conditions is also indispensable. Increasing the reaction temperature and the ratio between the concentrations of the less and more polar reactants, as well as a proper choice of the solvent polarity, are simple and complementary solutions to limit the negative effect of competition for adsorption between reactant and product molecules within the zeolite micropores. [Pg.61]

The structure-property relationship of flotation agents is determined by three factors related to structure bonding, hydrophilic-hydrophobic property and steric interactions. A number of quantitative criteria such as molecular orbital (MO) index, group electronegativity and hydrophilic-hydrophobic balance (HHB) has been used. [Pg.193]

The most important properties of amino acids, for the purpose of understanding protein structure and function, are electrostatic charge, hydrophilic/hydrophobic properties, and chemical reactivity, which are discussed below. [Pg.92]

This means that the ratio of furanosides to pyranosides obtained will depend on the conversion-contact time. If reaction of the glucosides is taken to the thermodynamic equilibrium the pyranoside to furanoside ratio is ca 95 5 and the molai ratio of aip is 65 35. The thermodynamic composition of the isomers varies from one monosaccharide to another [5]. A side-reaction is the oligopolymeriza-tion of the sugar with formation of alkyl polyglycosides. An average polymerization degree is defined APG) that influences the final hydrophilic-hydrophobic properties [6]. [Pg.258]

Adsorption on the LL interface can be observed in voltammetric curves, but a more sensitive indication of adsorption can be obtained from impedance measurements. Voltammetric studies (26, 27) showed that the addition of proteins to a so-called blocked (i.e., ideally polarizable) aqueous-nitrobenzene interface resulted in narrowing of the potential window of the supporting electrolyte system. This observation implies that the difference in hydrophilic-hydrophobic properties of the two solvents decreased. This decrease can be explained by postulating the formation of a third phase between the original two. The third phase would allow mediated, easier transport of the supporting electrolyte ions. [Pg.79]

Improve performance by optimizing hydrophilic/hydrophobic properties of the cathode. [Pg.442]

Through a wide range of aqueous phase concentrations, strong mono-protic acids, such as HCl, are extracted in a single mechanism—ion-pair formation. In addition, extraction is so efficient that virtually all the acid is present in the organic phase. Therefore, Grinstead s assumption that at half-neutralization [B] = [BH is adequate. Carboxylic acids, on the other hand, are much weaker and their extraction is less efficient. Apart from acidity, their distribution is affected by their hydrophilic-hydrophobic properties. In addition, the extraction is not necessarily through ion-pair forma-... [Pg.35]

Other related co-monomers were also studied. These included 7V-(hydroxy-methyl)acrylamide (HMA), methacrylamide, and iV,A/-dimethylacrylamide. The copolymerization of styrene with HMA led to less water-soluble polymer in the serum than in the case of copolymers of acrylamide and styrene. This may be attributable to differences in the hydrophilic-hydrophobic properties of acrylamide and HMA. Some monodisperse latices were prepared from styrene-HMA-water systems by procedures similar to Procedure 12-2. At a ratio of HMA to styrene of 0.2 to 1.0 the reported particle diameter was 0.3 /im with good size uniformity. It was projected that even better uniformity would be obtained when the ratio of HMA to styrene is 0.09 to 1.0. Either potassium persulfate or Af,A -azobisisopropylamidine hydrochloride has been used as initiators with similar results. Latices were generally purified by repetitive centrifiigation-decantation-redispersion cycles. [Pg.398]

POROUS STRUCTURE AND HYDROPHILIC-HYDROPHOBIC PROPERTIES OF HIGHLY DISPERSED CARBON ELECTRODES... [Pg.272]

FIGURE 2.71 Examples of cations and anions used in the formation of ILs, together with changes in hydrophilic-hydrophobic properties associated with anion type. (Ye, Y. S., J. Rick, and B. J. Hwang. 2013. Ionic liquid polymer electrolytes. Journal of Materials Chemistry A 1 2719-2743. Reproduced by permission of The Royal Society of Chemistry.)... [Pg.153]

Another typical photoresponsive material for preparation of switchable surfaces is the spiropyran-merocyanine system. The spiropyran isomerizes to zwitterionic merocyanine conformation by UV exposure, and the reverse reaction can be triggered by irradiation with visible light as well as azobenzene. The changes in hydrophilic/hydrophobic properties through the isomerization of spiropyran groups also enable the control of cell adhesion/ detachment. Edahiro et al. reported photoresponsive cell culture substrates grafted... [Pg.287]

An UBM laser profllometer was used to quantify the surface texture of features in excess of approximately >0.1 pm in terms of an average roughness, The hydrophilic/hydrophobic properties of the surfaces were assessed through measurements of dynamic contact angle (CAHN Dynamic Contact Angle analyzer) (Gun ko et al. 2011b). [Pg.709]


See other pages where Hydrophobic/hydrophilic properties is mentioned: [Pg.789]    [Pg.225]    [Pg.357]    [Pg.160]    [Pg.169]    [Pg.122]    [Pg.455]    [Pg.180]    [Pg.159]    [Pg.440]    [Pg.210]    [Pg.244]    [Pg.357]    [Pg.169]    [Pg.147]    [Pg.2915]    [Pg.1310]    [Pg.281]    [Pg.1089]    [Pg.295]    [Pg.490]    [Pg.272]    [Pg.273]    [Pg.153]    [Pg.393]    [Pg.280]    [Pg.819]    [Pg.206]    [Pg.13]   
See also in sourсe #XX -- [ Pg.193 ]




SEARCH



Hydrophilic properties

Hydrophilic/hydrophobic copolymers surface properties

Hydrophilicity-hydrophobicity

Hydrophilicity/hydrophobicity properties

Hydrophilicity/hydrophobicity properties

Hydrophilicity/hydrophobicity properties biodegradation mechanisms

Hydrophilicity/hydrophobicity properties block copolymers

Hydrophilicity/hydrophobicity properties polymers

Hydrophobic properties

Hydrophobic-hydrophilic

Porous Structure and Hydrophilic-Hydrophobic Properties of Highly Dispersed Carbon Electrodes

Properties hydrophobicity

Textile fibers hydrophobic/hydrophilic, properties

© 2024 chempedia.info