Humidity defined

To reach a lower moisture level, the polymer must be exposed to a dry air environment. Thus, relative humidity and dewpoint comprise the second fimdamental drying parameter. Relative humidity defines the amount of moisture a sample of air holds, compared to the amount it could hold at saturation. Dewpoint expresses how much moisture is in an air sample when it is at 100% relative humidity. 

The humidities for systems other than air and water are defined in an analogous manner. 

Effective temperature (ET ) is a single number representing those combinations of temperature and humidity which are equivalent in terms of comfort. It is defined as the dry-bulb temperature of the environment at 50% relative humidity. Standard effective temperature loci for normally clothed, sedentary persons are plotted on Eigure 3. The sensation of comfort depends in part upon the wetness of one s skin. Thus, as a person becomes more active the effective temperature lines become more hori2ontal and the influence of relative humidity is more pronounced. 

Dehydration Processing. Dehydration is one of the oldest means of preserving food. Microbes generally do not grow below a minimum water activity, of 0.65 defined as the equiHbrium relative humidity surrounding food ia a sealed container at a given temperature, ie, no microbes can... 

Percentage absolute humidity (percentage saturation) is defined as the ratio of absolute humidity to saturation humidity and is given by 100 H/H, = IQOpiP - p.VlpXP - p)]. 

Percentage relative humidity is defined as the partial pressure of water vapor in air divided by the vapor pressure of water at the given temperature. Thus RH = lOOp/p,. 

Fiber-saturation point is the moisture content of celhilar materials (e.g., wood) at which the cell walls are completely saturated while the cavities are liquid-free. It may be defined as the equihbrium moisture content as the humidity of the surrounding atmosphere approaches saturation. 

I. The wet-bulb or saturation temperature line gives the maximum weight of water vapor that I kg of dry air can cariy at the intersecting dry-bulb temperature shown on the abscissa at saturation humidity. The partial pressure of water in air equals the water-vapor pressure at that temperature. The saturation humidity is defined by... 

Special provisions are laid down in lEC 60079-0 and lEC 60079-1 for motors required for such locations in view of fluctuating degrees of humidity and temperature. Such locations are defined with a surface temperature limit of 150°C where coal dust can form a layer, or 450°C where it is not expected to form a layer. Otherwise, other details are generally the same as for flameproof motors type Ex d , according to lEC 60079-1. For variations in length of paths, gaps, widths, creepage and clearance distances, the reader should consult these Standards. 

A recovery of 5% of the total sample from the back-up section of charcoal in a sample tube was defined as the breakthrough point 50% of this value is shown as the recommended maximum tube loading, to allow for high humidity or the presence of other substances which reduce the normal tube capacity. 

The percent relative humidity is defined as lOOp/P, where p is the actual partial pressure of the water vapor and P is the vapor pressure of water at the same temperature. The total pressure is taken as normal barometric, unless otherwise stated. Note that since the per cent relative humidity is defined as 100(p/Pj) and the per cent absolute humidity equals 100[p/(760-p) -h P,/(760-Pj)], the factor by which the former must be multiplied to convert it to the latter is (760 -P ) / (760-p), where p and Pj can be expressed in units of millimeters of mercury. 

Figure 28 shows the key features of the humidity chart. The chart consists of the following four parameters plotted as ordinates against temperature on the abscissas (1) Humidity H, as pounds of water per pound of dry air, for air of various relative humidities (2) Specific volume, as cubic feet of dry air per pound of dry air (3) Saturated volume in units of cubic feet of saturated mixture per pound of dry air and (4) latent heat of vaporization (r) in units of Btu per pound of water vaporized. The chart also shows plotted hiunid heat (s) as abscissa versus the humidity (H) as ordinates, and adiabatic humidification curves (i.e., humidity versus temperature). Figure 28 represents mixtures of dry air and water vapor, whereby the total pressure of the mixture is taken as normal barometric. Defining the actual pressure of the water vapor in the mixture as p (in units of mm of mercury), the pressure of the dry air is simply 760 - p. The molal ratio of water vapor to air is p/(760-p), and hence the mass ratio is ... 

The saturated volume at 100 F is then 14.09+0.97 = 15.06. A eurve of sueh values is shown in Figure 28. Sinee humid volume is defined as the volume of any mixture, expressed as eubic feet of mixture per pound of dry air, and since both the specific and saturated values are on the basis of 1 lb of dry air, the humid volume for any humidity may be obtained directly by interpolation between the curves for specific and saturated volumes. 

We denoted the mass of dry air in a volume V as that is, p, - w,/Vj, and the mass of water vapor in V as m, that is, pp = mp/Yp. In practical calculations we usually handle volume flow volume flow is known in the suction inlet of a fan when the operating point of the fan is defined. Volume flow q, expressing the total air flow or the combined volume flow of water vapor and dry air, is not constant in various parts of the duct, because the pressure and temperature can vary. Therefore in technical calculations dealing with humid air, materia flows are treated as mass flows. Also, while the humidity can vary, the basic quantity is dry air mass flow w,(kg d.a./s). If, for instance, we know the volume flow q,. of a fan, the dry air mass flow through the fan is... 

The relative vapor pressure of air or the relative humidity is defined by the equation... 

Even if the receptor by itself has high accuracy, the sensor may be unable to execute the measurement in a defined place. Quality and total accuracy depend on the combination of receptor, the converter for measured values, and mechanical protection. Mechanical protection can take the form of pockets in water and fluid and also assembly boxes which protect against pollution, humidity, and temperature in the surroundings or against electromagnetic transmissions and noise from power-supplied pipes and cables. 

In certain computer models, a user-defined temperature, humidity, or contaminant concentration gradient can he considered. Nevertheless, this gradient is preset in the input and is not recalculated by the program on the basis of the results ot the previous time step. 

Textile engineer Stuart Cramer first published the term air conditioning in 1906, and G. B. Wilson defined air conditioning as the control of temperature, humidity, and air quality in 1908. 

---