Hardening crystals

Cp is tire number of elasticity active chains per volume unit. The comparison between experimental data and tire prediction by (C2.1.20) shows a reasonable agreement up to large defonnation (figure C2.1.16). For large values of X, strain hardening arises because of tire limited extensibility of tire chains or because of shear-induced crystallization. 

Ruthenium is a hard, white metal and has four crystal modifications. It does not tarnish at room temperatures, but oxidizes explosively. It is attacked by halogens, hydroxides, etc. Ruthenium can be plated by electrodeposition or by thermal decomposition methods. The metal is one of the most effective hardeners for platinum and palladium, and is alloyed with these metals to make electrical contacts for severe wear resistance. A ruthenium-molybdenum alloy is said to be... 

Because the time at high temperature is much less, austenite is produced, which is chemically inhomogeneous especially with undissolved carbides, and has a fine grain crystal size. The formation of the hard martensite requites more rapid cooling than for conventional hardening. Thus case hardening by heat treatment intrinsically requites that the surface region to be hardened be relatively thin and cooled rapidly. 

Structure and Crystallinity. The mechanical—optical properties of polycarbonates are those common to amorphous polymers. The polymer may be crystallized to some degree by prolonged heating at elevated temperature (8 d at 180°C) (16), or by immersion ia acetone (qv). Powdered amorphous powder appears to dissolve partially ia acetone, initially becoming sticky, then hardening and becoming much less soluble as it crystallizes. Enhanced crystallization of polycarbonate can also be caused by the presence of sodium phenoxide end groups (17). 

Crystallization. Raw natural mbber may freeze or crystallize during transit or prolonged storage, particularly at subzero temperatures. The mbber then becomes hard, inelastic, and usually much paler in color. This phenomenon is reversible and must be differentiated from storage hardening. The rate of crystallization is temperature-dependent and is most rapid at —26° C. Once at this temperature, natural mbber attains its maximum crystallinity within hours, and this maximum is no more than 30% of the total mbber. 

Extrusion Resins. Extmsion of VDC—VC copolymers is the main fabrication technique for filaments, films, rods, and tubing or pipe, and involves the same concerns for thermal degradation, streamlined flow, and noncatalytic materials of constmction as described for injection-molding resins (84,122). The plastic leaves the extmsion die in a completely amorphous condition and is maintained in this state by quenching in a water bath to about 10°C, thereby inhibiting recrystallization. In this state, the plastic is soft, weak, and pHable. If it is allowed to remain at room temperature, it hardens gradually and recrystallizes partially at a slow rate with a random crystal arrangement. Heat treatment can be used to recrystallize at controlled rates. 

It was ironic that a few years later, Rosenhain began to insist that the material inside the slip bands (i.e., between the layers of unaffected crystal) had become amorphous and that this accounted for the progressive hardening of metals as they were increasingly deformed there was no instrument to test this hypothesis and so it was unfruitful, but none the less hotly defended ... 

Mott played a major part, with his collaborator Frank Nabarro (b. 1917) and in consultation with Orowan, in working out the dynamics of dislocations in stressed crystals. A particularly important early paper was by Mott and Nabarro (1941), on the flow stress of a crystal hardened by solid solution or a coherent precipitate, followed by other key papers by Koehler (1941) and by Seitz and Read (1941). Nabarro has published a lively sequential account of their collaboration in the early days (Nabarro 1980). Nabarro originated many of the important concepts in dislocation theory, such as the idea that the contribution of grain boundaries to the flow stress is inversely proportional to the square root of the grain diameter, which was later experimentally confirmed by Norman Fetch and Eric Hall. 

Engelhard s in-situ FCC catalyst technology is mainly based on growing zeolite within the kaolin-based particles as shown in Figure 3-9A. The aqueous solution of various kaolins is spray dried to form micR)spheres. The microspheres are hardened in a high-temperature l,3f)(TF/704°C) calcination process. The NaY zeolite is produced by digestion of the microspheres, which contain metakaolin, and mullite with caustic or sodium silicate. Simultaneously, an active matrix is formed with the microspheres. The crystallized microspheres are filtered and washed prior to ion exchange and any final treatment. 

---