Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Centerless grinding

Grinding Cylindrical grinding Centerless grinding roughing finishing ... [Pg.470]

Rubber. Both natural and synthetic rubber are used as bonding agents for abrasive wheels. Rubber-bond wheels are ideal for thin cut-off and slicing wheels and centerless grinding feed wheels. They are more flexible and more water-resistant than resinoid wheels. [Pg.15]

Annealed in oxygen after polishing hy centerless grinding 1040... [Pg.882]

Grinding Pellet loading and fuel pin assembly Decontamination Centerless (dry)... [Pg.573]

Centerless grinding Points Internal wall of round hole... [Pg.464]

External grinding Center ground and centerless tolerance parallelism 0.0005 0.0005 0.0001 0.0002 ... [Pg.470]

Centerless grinding is a cylindiical grinding process variant without fixing the workpiece along its axis between centers. [Pg.135]

In external centerless grinding, the workpiece lies between grinding wheel, workrest plate, and control wheel which regulates the speed of the workpiece. In internal centerless grinding, the workpiece lies between rolls or shoes and is driven by a control wheel or a faceplate. [Pg.135]

If possible, control wheel and workrest plate support the workpiece on the machined circumferential area to avoid bending. However, this three-point support can induce self-regenerative roundness errors as explained in the next section. In centerless grinding the radial feed is relative to the workpiece diameter, not the radius as in grinding between centers (Marinescu et al. 2007). Therefore, the depth of cut, Ug, per work-piece revolution can be calculated as... [Pg.136]

In centerless grinding the workpiece is machined and supported on its circumferential area, which... [Pg.136]

Most research on stability focuses on centerless plunge grinding as a two-dimensional setup. However, Meis, Barrenextra, and others deducted stability conditions for throughfeed grinding adding a third dimension to the stabihty conditions (Meis 1981 Barrenetxea et al. 2009, etc.). [Pg.137]

Internal centerless grinding works with grinding wheel, control wheel, support roll, and pressure roll to fix the workpiece. The external workpiece surface provides the reference for concentricity and roundness of the inner diameter (Marinescu et al. 2007). [Pg.137]

Shoe centerless grinding can be applied to external and internal cylindrical surfaces and is especially important for small length-to-diameter ratio. In shoe grinding the component is positioned by shoes instead of control wheel and workrest plate (Marinescu et al. 2007). [Pg.137]

Bhateja CP, Levi R (1984) Current state of the Art of workpiece roundness control in precision centerless grinding. CIRP Ann Manuf Technol 33(l) 199-203... [Pg.138]

Dali, AH (1946) Rounding effect in centerless grinding. Mechanical Engineering, ASME, 58 325-329... [Pg.138]

Furukawa Y, Miyashita M, Shiozaki S (1971) Vibration analysis and work-rounding mechanism in centerless grinding. Int J Mach Tool Des Res 11(1971) 145-175... [Pg.138]

Hashimoto F, Zhou SS, Lahoti GD, Miyashita M (2000) Stability diagram for chatter free centerless grinding and its application in machine development. Ann CIRP 49(l) 225-230... [Pg.138]

Miyashita M, Hashimoto F, Kanai F (1982) Diagram for selecting chatter free conditimis of centerless grinding. CIRP Ann Manuf Technol 31(1) 221—223... [Pg.138]

Rowe WB (1964) Some Studies of the Centerless Grinding with Particular reference to the Roundness Accuracy. PhD-thesis at University of Manchester... [Pg.138]

See other pages where Centerless grinding is mentioned: [Pg.106]    [Pg.106]    [Pg.141]    [Pg.300]    [Pg.342]    [Pg.106]    [Pg.106]    [Pg.141]    [Pg.300]    [Pg.342]    [Pg.881]    [Pg.882]    [Pg.183]    [Pg.184]    [Pg.104]    [Pg.135]    [Pg.135]    [Pg.135]    [Pg.136]    [Pg.136]    [Pg.136]    [Pg.136]    [Pg.136]    [Pg.136]    [Pg.137]    [Pg.137]    [Pg.137]    [Pg.137]    [Pg.137]    [Pg.137]    [Pg.138]    [Pg.138]    [Pg.138]    [Pg.138]   
See also in sourсe #XX -- [ Pg.300 ]



SEARCH



© 2024 chempedia.info