Lubricants graphite

Graphite lubricants include the dry powder, admixtures with liquid lubricants or greases, volatile liquids compounded with film-forming substances to produce bonded dry films, synthetic resins and powder metal compositions containing graphite for bearings, and finely divided suspensions in liquids (colloidal graphite). [Pg.577]

Brake Linings. Substantial amounts of crystalline flake, lump, and amorphous graphite are used in brake and clutch finings, mostly in heavier duty nonautomotive situations. The graphite has been substituted for asbestos because of health considerations. The graphite proportion of the part has risen from 2 to 15% in some instances. The graphite lubricates, transfers the heat of friction away from the fining, and lowers the rate of wear. [Pg.577]

R. H. Heiskell, 50, 8208 (1956) Claims highly stable, dark-burning igniter compns containing Bi203 45-85, Mn 15-55, stearic acid binder up to 10, and graphite lubricant up to 10% USP 2716599 (1955) USP 2726944 (1956)... [Pg.282]

Graphite Lubricants, crucibles, electrical components, pencils, nuclear moderator Mexico, Canada, Sri Lanka, Madagascar 100... [Pg.11]

Bragg, W.L., Introduction to Crystal Analysis, Bell Son, London, (1928). Savage, R.H., Graphite Lubrication, J. Appl. Phys., 19, 1, (1948). [Pg.362]

After the required amount of hydrogen has been taken up, the bomb is stopped in the up position, and the heater is shut off. After the bomb has cooled, the remaining pressure is released through the hydrogen vent, which should lead the hydrogen out into a well-ventilated open area. The bomb may then be removed from the jacket and opened, and the contents removed. It is essential that the bomb be thoroughly cleaned with solvents after each use, for if the bomb becomes pitted, it may hold onto compounds which will poison the catalyst. The threads should be cleaned off and wiped with a graphite lubricant so that the cap will not freeze onto the bomb. [Pg.235]

Aquadag, Oildag, graphite, analysis theory of graphite lubrication... [Pg.256]

Typical fillers carbon fiber, glass fiber, graphite lubricant for wear resistant applications molybdenum sulfide, PTFE. antimony trioxide, barium titanate, clay, silica, aluminum nitride, smectite... [Pg.656]

Coal and limestone samples are both cylindershaped, and have size of 4>50 mm x 50 mm. Parallel degree was controlled within the range of 0.02 mm error in the sample processing to guarantee the surface cleanliness. In order to reduce the friction effect between the pressure bar and the specimen, ensure good contact and meet the SHPB uniformity assumption, graphite lubricant is evenly smeared on the two ends of specimens. [Pg.52]

PEG-23M PEG-45M PEG-2 oleate PEG-4 stearate PEG-8 stearate PEG-12 stearate Poloxamer 182 Poloxamer 185 Poloxamer 188 Poloxamer 231 Poloxamer 234 Poloxamer 235 Poloxamer 238 Poloxamer 282 Poloxamer 288 Poloxamer 331 Poloxamer 333 Poloxamer 334 Poloxamer 335 Poloxamer 338 Poloxamer 401 Poloxamer 402 Poloxamer 403 Polysorbate 61 Propylene glycol laurate Propylene glycol myristate Synthetic wax Vegetable oil lubricant, paints/coatings Graphite lubricant, paper... [Pg.5445]

Other techniques can be used to prevent fibers sticking during stabilization and are generally based on a form of a carbon/graphite lubricant, such as colloidal graphite, or carbon black in aqueous or silicone oil suspension and applied to the fiber prior to stabilization. Although it is reported that suspensions of silica and calcium carbonate... [Pg.300]

PI, 25% graphite lubricated Valves seals, compressor rings - - -... [Pg.222]

Spray Graph, Graphite lubricant, American Resin Cap. [Pg.936]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...