Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Finished Cement Grinding

Four-stage suspension preheater with a precalciner at a Portland Cement plant.3 [Pg.203]

Finish mill grinding and shipping during Portland Cement manufacture.3 [Pg.205]


Calcined clinker is ground in ball mills, mixed with gypsum, and shipped in bags or bulk. Figure 4-7 depicts finish mill grinding and cement shipping. The type of fuel used to make clinker does not affect these operations. [Pg.202]

Polymethacrylic acid CAS 25087-26-7 Synonyms PMAA Classification Polymer Empirical (C4He02)x Formula [CHzCCHaCOOHlx Uses Dispersant for pigments and fillers in ceramics, polymerization dispersant in boiler water treatment cement grinding aid textile soil-release finishes rayon textile sizing agent stabilizer for PVC suspension prod. vise, control agent in cosmetics Manuf./Distrib. Al co... [Pg.3530]

The finished cement that is discharged from the clinker grinding mill is stored in silos in which it should, ideally, undergo no subsequent changes. However, certain influences may act upon the cement in storage and have a detrimental effect on its quality. [Pg.488]

Finishing cements and raw mixes typically contain Ca, Si, Al and O at high concentrations, plus Fe, K, Mg and Na at low concentrations. One of the major problems in accurate cement analysis is homogeneity, particularly in the case of raw mixes, where the source of raw material may be variable. Most of the elements to be determined are of low atomic number, hence the penetration of their characteristic lines will be of the order of a few micrometres only. Careful grinding and pelletizing will suffice, but the fusion bead technique with Li3B04 is strongly recommended. Simultaneous multichannel WD systems are ideally suited for this kind of application. [Pg.1308]

A wet-process plant maldug cement from shale and hmestoue has been described by Bergstrom [Roc/c Prod., 64—71 (June 1967)]. There are separate facilities for grinding each type of stone. The ball mill operates in closed circuit with a battery of Dutch State Mines screens. Material passing the screens is 85 percent minus 200 mesh. The entire process is extensively instrumented and controlled by computer. Automatic devices sample crushed rock, slurries, and finished product for chemical analysis by X-rav fluorescence. Mill circuit feed rates and water additions are governed by conventional controllers. [Pg.1871]

The manufacture of Portland concrete consists of three basic steps—crushing, burning, and finish grinding. As noted earlier, Portland cement contains about 60% lime, 25% silicates, and 5% alumina with the remainder being iron oxides and gypsum. Most cement plants are located near limestone (CaCOs) quarries since this is the major source of lime. Lime may also come from oyster shells, chalk, and a type of clay called marl. The silicates and alumina are derived from clay, silicon sand, shale, and blast-furnace slag. [Pg.385]

Finish-Grinding of Cement Clinker Typically the hot clinker is first cooled and then ground in a compartment mill in closed circuit with an air classifier. To crush the clinkers, balls as large as 5 in may be needed in the first compartment. A roll press added before the ball mill can reduce clinkers to a fine size, and thus reduce the load on the ball mills. The main reasons for adding a roll press has been to increase capacity of the plant, and lower cost. [Pg.1630]

Massive forms are in use as cast only. Finished shape can be attained by grinding, since they are not amenable to hot rolling or forging. The properties of stellite metal cutting tools are in the middle between HSS and cemented carbides. Other applications are wear and corrosion resistant parts, like pump sleeves, valves, valve seats, extrusion dies, and mill guides. [Pg.319]

USE Chiefly in lacquers and varnishes also in manuf buttons, grinding wheels, sealing wax, cements, inks, phonograph recorda, papar for stiffening hats in electrical machines coating confections and medicinal tablets finishing leather. [Pg.1344]

Thin-film diamond and diamond-Uke coatings are deposited on finish-groimd cemented carbide tools such as end-mills and drills. The main benefit of CVD diamond coatings is that there is no subsequent grinding or finishing operation on the tool necessary. [Pg.1183]

C. Cement chemistry - cement quality V. Finish grinding... [Pg.79]


See other pages where Finished Cement Grinding is mentioned: [Pg.202]    [Pg.1353]    [Pg.4097]    [Pg.2454]    [Pg.202]    [Pg.1353]    [Pg.4097]    [Pg.2454]    [Pg.293]    [Pg.2313]    [Pg.325]    [Pg.2296]    [Pg.71]    [Pg.359]    [Pg.207]    [Pg.216]    [Pg.443]    [Pg.293]    [Pg.1820]    [Pg.227]    [Pg.443]    [Pg.207]    [Pg.216]    [Pg.1579]    [Pg.2245]    [Pg.72]    [Pg.2228]    [Pg.19]    [Pg.1824]    [Pg.1064]    [Pg.1335]    [Pg.3905]    [Pg.182]    [Pg.970]    [Pg.142]    [Pg.827]   


SEARCH



Finish grinding

Finish-Grinding of Cement Clinker

© 2024 chempedia.info