Finish insert

Finish insert (neck insert). In blow molding bottles, a removable part of the mold that aids in forming a specific neck finish of the bottle. 

Metal Pan Assemblies. These units consist of tiles and panels formed from perforated aluminum or steel with pads of fiber glass or mineral wool inserted into the pans to provide the sound absorption. They are used primarily for ceilings in a similar manner to acoustical tiles and panels. The pads are sometimes sealed in plastic film to prevent absorption of moisture, dirt, and odors. The perforated metal is relatively sound transparent and functions as the finished ceiling and the support for the sound-absorbing material. The perforated metal by itself has no acoustical value. 

The key to solving these problems is to design the vessel for a mass flow pattern. This involves consideration of both the hopper angle and surface finish, the effect of inserts used to introduce gas and control the soHds flow pattern, and sizing the outlet valve to avoid arching and discharge rate limitations. In addition, the gas or Hquid must be injected such that the soHd particles ate uniformly exposed to it, and flow instabiHties such as fluidization in localized regions are avoided. 

Gel coats are typicaHy used to provide a part with a finished surface directly from the mold. Various inserts, stiffeners, and mechanical attachments can be incorporated in the mol ding step, thereby further reducing secondary operations. Final edge trimming is accompHshed with a variety of tools such as... 

A special attribute of these processes is the abiHty to pre-position reinforcement, inserts, and core materials for stiffening ribs. Gel coatings can be apphed to the mold surface to eliminate post-mold finishing. Because both surfaces of the part are formed in a mold to close tolerances, accurate assemblies are possible, which is a requirement for many automotive or tmck body appHcations. 

No dimensional change Used chiefly for finished work where heating may be undesirable where inserts are present... 

The old dry process enamelling of cast iron (baths etc.) is no longer widely used. The method consisted of sieving finely powdered frit onto the preheated casting and inserting the casting back into a furnace at about 900°C to produce the smooth finish. 

Coupons These are usually strip, flush discs or cylindrical rods mounted in suitable racks (inserted and retrieved at shutdown), or installed in the plant using high-pressure access systems. Coupons are available from several manufacturers in a variety of materials and surface finishes and are supplied pre-weighed. 

This term is used both to describe designs that are etched or engraved in the mold surface and the process of inserting a printed film into the mold, to be produced as an integral component of the finished product. Etched surfaces can be drawn both parallel and perpendicular to a parting line of molds or postforming in an extrusion line.. However, be alert with molds to the fact that parallel to the parting line additional draft is required. A wide selection of patterns is available and new ones can be readily created. 

Another consideration is the ability of a material to provide a surface that is compatible with the requirements of the application a smooth finish for extruded profiles, molded-in colors, textured surfaces, etc. The compatibility of the major processes with in-mold coating and other insert-surfacing materials, and their compatibility with surface decoration secondary processes, could also be important. 

Insert new ring 1 week after the last ring removed on the same day of the week as it was inserted in the previous cycle. Do this even if bleeding is not finished. 

The juice is recovered by inserting tubular knives into the fruit and squeezing the fruit. Alternatively, the fruit may be cut in half and squeezed. The recovered juice is put through a finisher to remove a portion of the pulp sacs, is heated to inactivate enzymes, and is either bottled as single-strength juice or concentrated for frozen concentrate. 

Initially a map of minimal size is prepared that consists of as few as three or four nodes. Since the map at this stage is so small, it is very quick to train. As training continues and examples of different classes are discovered in the database, the map spreads itself out by inserting new nodes to provide the extra flexibility that will be needed to accommodate these classes. The map continues to expand until it reaches a size that offers an acceptable degree of separation of samples among the different classes. As in a SOM, on the finished map, input patterns that are similar to one another should be mapped... 

We will finish the example with a couple of points which will prove useful later in the chapter. If we insert the harmonic oscillator potential into the temperature correction formula (11.2), we get... 

Variations The poly(A) tailing kit (Ambion) produces a mRNA population with varying lengths of poly(A) tails, controlled by altering poly(A) polymerase concentrations and incubation times. An alternate method to incorporate a poly(A) tail is to clone a defined stretch of adenosines/ thymidines into the > UTR of the template pDNA. To allow transcripts to finish on an adenosine, the insert should be followed by a restriction site for an enzyme that cleaves 5 of the last antisense strand thymidine, such as Nsi I. In this way, the poly (A) tail can be incorporated directly into the... 

Pipe component ends shall be trimmed as shown in Figs. GR-3.4.3(c) and (e) to correct internal misalignment. Such trimming shall not reduce the finished wall thickness below the required minimum wall thickness, tm. To fit backing rings, see Figs. GR-3.4.3(f) and (g), or for consumable inserts, see Fig. GR-3.4.3(h). 

---