Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Parting lines

Beeause the width of the seetion is over a parting line, the only proeess risk is a geometry to proeess risk = 1.7 whieh gives the adjusted toleranee as ... [Pg.217]

Check parting-line surfaces for full contact. Stone or lap if burrs or raised edges exist. [Pg.756]

This type of mould, also often referred to as a three plate mould, is used when it is desired to have the runner system in a different plane from the parting line of the moulding. This would be the case in a multi-cavity mould where it was desirable to have a central feed to each cavity (see Fig. 4.38). In this type of mould there is automatic degating and the runner system and sprue are ejected separately from the moulding. [Pg.290]

Parting line must be taken into consideration. [Pg.165]

Tolerances are based on 0.125 inch wall section. Parting line must be taken into consideration. [Pg.167]

Parting line must betaken into consideration. [Pg.168]

Many injection molded products will influence the final product s performance, dimensions, and other characteristics. The mold includes the cavity shape, gating, parting line, vents, undercuts, ribs, hinges, and so on (Table 3-17). The mold designer must take all these factors into account to eliminate problems. At times, to provide the best design... [Pg.181]

Parting line PLs on the surface of a molded product, which are produced by the parting line of the mold, when required can often be concealed on a thin, inconspicuous edge of the product. Doing so preserves the good appearance of the molding and in most cases eliminates the need for any finishing. [Pg.185]

By contrast with ICM, a compression mold design is used where male plug fits into a female cavity rather than the usual flat surface parting line mold halves for IM (Fig. 8-27). The melt is injected into the cavity as a short shot thereby not filling the cavity. The melt in the cavity is literally stress-free it is literally poured into the cavity. Prior to receiving melt, the mold is slightly opened so that a closed cavity exists the male and female parts... [Pg.472]

Basically the BM lines have an extruder with a die or an injection machine with a mold to form the parison or preform, respectively. In turn the hot parison or preform is located in a mold. Air pressure through a tubular pin-type device located usually at the parting line of the mold will expand the parison or preform to fit snugly inside their respective mold... [Pg.487]

This term is used both to describe designs that are etched or engraved in the mold surface and the process of inserting a printed film into the mold, to be produced as an integral component of the finished product. Etched surfaces can be drawn both parallel and perpendicular to a parting line of molds or postforming in an extrusion line.. However, be alert with molds to the fact that parallel to the parting line additional draft is required. A wide selection of patterns is available and new ones can be readily created. [Pg.538]

Design Considerations for Injection Molded Parts (Parting lines, draft angles, wall thickness, fillets and radii, bosses, ribs, opening formations, shrinkage, gating, vents, potential knit lines)... [Pg.626]

When a parison or preform is inflated, it displaces the air around it within the mold. If no provision is made to vent the mold, compression of the air around the parison or preform can raise its temperature to such an extent that it can scorch the surface of the product. To avoid this problem, we equip blow molds with vents. These can consist of slit vents at the parting line between mold halves, porous plugs of sintered metal, or small holes drilled into the cavity walls. [Pg.257]

For applications requiring two different compounds, such as a double hardness sealing ring or a two colour rubber shoe sole, some machines have two injection units. One injects into the bottom/centre mould plate and the other into the parting line. Two injection units on a singlestation vertical press are used in combination with twin rotating cavity plates. [Pg.191]


See other pages where Parting lines is mentioned: [Pg.530]    [Pg.412]    [Pg.412]    [Pg.9]    [Pg.245]    [Pg.232]    [Pg.43]    [Pg.45]    [Pg.53]    [Pg.89]    [Pg.89]    [Pg.315]    [Pg.293]    [Pg.309]    [Pg.598]    [Pg.1018]    [Pg.1018]    [Pg.10]    [Pg.156]    [Pg.176]    [Pg.179]    [Pg.199]    [Pg.200]    [Pg.201]    [Pg.441]    [Pg.446]    [Pg.451]    [Pg.459]    [Pg.470]    [Pg.517]    [Pg.534]    [Pg.538]    [Pg.637]    [Pg.689]    [Pg.256]   
See also in sourсe #XX -- [ Pg.608 ]

See also in sourсe #XX -- [ Pg.2 , Pg.3 , Pg.4 , Pg.5 , Pg.6 , Pg.7 , Pg.8 , Pg.9 , Pg.10 , Pg.11 , Pg.12 , Pg.13 , Pg.14 , Pg.15 , Pg.16 ]

See also in sourсe #XX -- [ Pg.41 ]

See also in sourсe #XX -- [ Pg.53 , Pg.393 ]

See also in sourсe #XX -- [ Pg.805 , Pg.843 ]

See also in sourсe #XX -- [ Pg.21 ]

See also in sourсe #XX -- [ Pg.262 , Pg.308 ]

See also in sourсe #XX -- [ Pg.3 , Pg.42 , Pg.49 , Pg.63 , Pg.129 , Pg.130 , Pg.131 , Pg.137 ]




SEARCH



© 2024 chempedia.info