Fiber-Reinforced Metals

Strength. Prediction of MMC strength is more compHcated than the prediction of modulus. Consider an aligned fiber-reinforced metal-matrix composite under a load P in the direction of the fibers. This load is distributed between the fiber and the matrix ... [Pg.200]

Maturation as a technology does not mean that advancement and innovation has ceased. Adhesive bonding is so essential to the aerospace field that as long as there is a desire to go higher, faster and farther more efficiently, there will be an incentive to develop new materials and processes for adhesive bonding. Areas of particular interest for future applications are high-temperature adhesives, fiber-reinforced metal laminates and more efficient bond assembly techniques. [Pg.1187]

Fiber-reinforced metal laminates have been developed in recent years and are slowly finding their way onto commercial aircraft. Fiber-reinforced metal... [Pg.1187]

Fiber-reinforced composites, subcritical damage mechanisms in, 16 188 Fiber-reinforced metal-matrix composites, 16 171... [Pg.355]

Kelly, A. and Tyson, W. R., Tensile properties of fiber reinforced metals copper tungsten and copper/molybdenum,. /. Mech. Phys. Solids, 13, 329 (1965). [Pg.560]

Chou. T.W.. Kelly, A. and Okura, A, (1985). Fiber reinforced metal matrix composites. Composites. 16, 187-206... [Pg.321]

Doghri, H., Jansson, S., Leckie, F.A. and Lemaitre (1990). Optimization of interface layers in the design of ceramic fiber reinforced metal matrix composites. NASA CR-185307. [Pg.321]

Jansson. S. and Leekie, F.A. (1992). Reduction of thermal stresses in continuous fiber reinforced metal matrix composites with interface layer. J. Composite Mater. 26, 1474-1486. [Pg.323]

Ceramic-Fiber Reinforced Metal-Matrix Composites (MMCs)... [Pg.317]

Stress Distribution and High Temperature Creep Rate of Discontinuous Fiber Reinforced Metals, Acta Metallurgies et Materialia, 38, 1941-1953 (1990). 26. A. G. Evans, J. W. Hutchinson, and R. M. McMeeking, Stress-Strain Behavior of Metal Matrix Composites with Discontinuous Reinforcements, Scripta Metallurgica et Materialia, 25, 3-8 (1991). [Pg.332]

At manufacturing level, chemical reactions between the matrix and the liber produce an interface zone of different mechanical properties from the two phases producing it [158]. The load of a composite is usually transferred through the interface between the matrix and the fiber, and the toughness of the composite is determined. Karpur et al. measured ultrasonically the shear stiffness coefficient of the interface in fiber reinforced metal matrix and ceramic matrix composites [158]. They claim that the significance of the quantification of the shear stiffness coefficient of the interface is that the clastic property of the interface can be used as a basis for composite life prediction. [Pg.823]

Fiber-reinforced metals are of interest because their high specific strengths, cr/p, and modulus, E/p, contribute to structural efficiency where weight or inertial forces are important. Of the many fiber-metal systems that have been studied, boron-reinforced aluminum is the most highly developed and the only one for which any cryogenic property data have been obtained Aluminum reinforced... [Pg.69]

Composite fabrication techniques were examined and in particular, the work of TW Thorpe on filament winding should be mentioned, basically for use with the classified centrifuge project for separation of uranium isotopes. Designing with cfrp has been covered by Pearce [112] and more specifically, designing with carbon fiber reinforced metals [113]. [Pg.89]

Bouix et al describe the interface tailoring of carbon fibers [14], whilst Lawcock et al [15] considered the effects of the fiber/matrix adhesion on the strength of carbon fiber reinforced metal laminates and the effects of the fiber/matrix adhesion on the impact strength of carbon fiber reinforced metal laminates [16]. [Pg.630]

TECHNIQUES FOR FABRICATING CARBON FIBER REINFORCED METAL... [Pg.641]

A number of useful reviews detailing composite fabrication have been written [43,116 122]. The general methods for forming carbon fiber reinforced metal matrix... [Pg.641]

The residual strength and impact behavior of the fiber/matrix on carbon fiber reinforced metal laminates has been studied [130,131]. [Pg.641]

Bouix J, Berthet MP, Bosselet F, Favre R, Peronnet M, Viala JC, Vincent C, Vincent H, Interface tailoring in carbon fibers reinforced metal matrix composites. Journal de Physique, IV 7(C6), 191-205, 1997. [Pg.649]

Lawcock GD, Ye L, Mai YW, Sun CT, Effects of fiber/matrix adhesion on carbon fiber reinforced metal laminates -1, Residual strength, Composites Sci Technol, 57(12), 1609-1619, 1997. [Pg.649]

Baker A A, Carbon fiber reinforced metals—a review of current technology, Mater Sci Eng, 17, 177, 1975. [Pg.650]

Interfacial Modifications and Bonding of Fiber Reinforced Metal Composite Material, In Yosomiya R, Morimoto K, Nakajima A, Ikada Y, Suzuki T eds.. Adhesion and Bonding in Composites, Marcel Dekker, New York, 235 256, 1990. [Pg.651]

The mechanism of friction and wear of carbon fiber reinforced metals has been studied [200-204]. [Pg.837]

Density of 55MSI Graphite/6061 Aluminum Composites Density of Graphite Fiber Reinforced Metals Density of Si3N4 Composites... [Pg.24]

Modulus of Elasticity of Graphite Fiber Reinforced Metals... [Pg.1522]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...