Ethylbenzene catalyst

Example 10.8 How fine would you have to grind the ethylbenzene catalyst for laboratory kinetic studies to give the intrinsic kinetics Assume the small pore diameter of Example 10.7. 

Use Ethylbenzene catalyst, dyestuff intermediate, detergent alkylate, ethyl chloride, pharmaceuticals and organics (Friedel-Crafts catalyst), butyl rubber, petroleum refining, hydrocarbon resins, nucleating agent for titanium dioxide pigments. 

Extraction of C-8 Aromatics. The Japan Gas Chemical Co. developed an extraction process for the separation of -xylene [106-42-3] from its isomers using HF—BF as an extraction solvent and isomerization catalyst (235). The highly reactive solvent imposes its own restrictions but this approach is claimed to be economically superior to mote conventional separation processes (see Xylenes and ethylbenzene). 

Friedel-Crafts alkylation using alkenes has important industrial appHcations. The ethylation of benzene with ethylene to ethylbenzene used in the manufacture of styrene, is one of the largest scale industrial processes. The reaction is done under the catalysis of AlCl in the presence of a proton source, ie, H2O, HCl, etc, although other catalysts have also gained significance. 

Sales demand for acetophenone is largely satisfied through distikative by-product recovery from residues produced in the Hock process for phenol (qv) manufacture. Acetophenone is produced in the Hock process by decomposition of cumene hydroperoxide. A more selective synthesis of acetophenone, by cleavage of cumene hydroperoxide over a cupric catalyst, has been patented (341). Acetophenone can also be produced by oxidizing the methylphenylcarbinol intermediate which is formed in styrene (qv) production processes using ethylbenzene oxidation, such as the ARCO and Halcon process and older technologies (342,343). 

Ethjlben ne Synthesis. The synthesis of ethylbenzene for styrene production is another process in which ZSM-5 catalysts are employed. Although some ethylbenzene is obtained direcdy from petroleum, about 90% is synthetic. In earlier processes, benzene was alkylated with high purity ethylene in liquid-phase slurry reactors with promoted AlCl catalysts or the vapor-phase reaction of benzene with a dilute ethylene-containing feedstock with a BF catalyst supported on alumina. Both of these catalysts are corrosive and their handling presents problems. 

These operations have been gradually replaced by the Mobd-Badger process (28), which employs an acidic ZSM-5 catalyst and produces ethylbenzene using both pure and dilute ethylene sources. In both cases, the alkylation is accomplished under vapor-phase conditions of about 425°C,... 

MPa (15—20 atm), 300—400 kg benzene per kg catalyst per h, and a benzene ethylene feed ratio of about 30. ZSM-5 inhibits formation of polyalkjlated benzenes produced with nonshape-selective catalysts. With both ethylene sources, raw material efficiency exceeds 99%, and heat recovery efficiency is high (see Xylenes and ethylbenzene). 

Vapor-Phase Processes. Although vapor-phase alkylation has been practiced since the early 1940s, it could not compete with Hquid-phase processes until the 1970s when the Mobil—Badger vapor-phase ethylbenzene process was introduced (Eig. 4). The process is based on Mobil s ZSM-5 zeohte catalyst (38,52,53). The nonpoUuting and noncorrosive nature of the process is one of its major advantages over the AlCl hquid-phase system. 

AlCl and Hydrogen Chloride Catalyst. Historically, AIQ processes have been used more extensively for the production of ethylbenzene than for the production of cumene. In 1976, Monsanto developed an improved cumene process that uses an AIQ. catalyst, and by the mid-1980s, the technology had been successfully commercialized. The overall yields of cumene for this process can be as high as 99 wt % based on benzene and 98 wt % based on propylene (60). 

Catalysts. Nearly aU. of the industrially significant aromatic alkylation processes of the past have been carried out in the Hquid phase with unsupported acid catalysts. For example, AlCl HF have been used commercially for at least one of the benzene alkylation processes to produce ethylbenzene (104), cumene (105), and detergent alkylates (80). Exceptions to this historical trend have been the use of a supported boron trifluoride for the production of ethylbenzene and of a soHd phosphoric acid (SPA) catalyst for the production of cumene (59,106). 

Two catalysts have emerged as commercially viable. The Mobil—Badger ethylbenzene process, which has been in commercial use since 1980, employs a ZeoHte catalyst and operates in the gas phase. A Hquid-phase ethylbenzene process joindy Hcensed by Lummus and UOP uses a Y-type ZeoHte catalyst developed by Unocal. This Hquid-phase process was commercialized in 1990. The same Y-type ZeoHte catalyst used for the production of ethylbenzene is being offered for the production of cumene but has not yet been commercialized. 

Process. As soHd acid catalysts have replaced Hquid acid catalysts, they have typically been placed in conventional fixed-bed reactors. An extension of fixed-bed reactor technology is the concept of catalytic distillation being offered by CR L (48). In catalytic distillation, the catalytic reaction and separation of products occur in the same vessel. The concept has been appHed commercially for the production of MTBE and is also being offered for the production of ethylbenzene and cumene. 

Acetophenone is separated for hydrogenation to 1-phenylethanol, which is sent to the dehydrator to produce styrene. Hydrogenation is done over a fixed-bed copper-containing catalyst at 115—120°C and pressure of 8100 kPa (80 atm), a 3 1 hydrogen-to-acetophenone ratio, and using a solvent such as ethylbenzene, to give 95% conversion of the acetophenone and 95% selectivity to 1-phenylethanol (186,187). 

Zeolite-Based All lation. Zeohtes have the obvious advantages of being noncorrosive and environmentally benign. They have been extensively researched as catalysts for ethylbenzene synthesis. Eadier efforts were unsuccessful because the catalysts did not have sufficient selectivity and activity and were susceptible to rapid coke formation and deactivation. 

A small fraction of the hydrocarbons decompose and deposit on the catalyst as carbon. Although the effect is minute ia terms of yield losses, this carbon can stiU significantly reduce the activity of the catalyst. The carbon is formed from cracking of alkyl groups on the aromatic ring and of nonaromatics present ia certain ethylbenzene feedstocks. It can be removed by the water gas reaction, which is catalyzed by potassium compounds ia the catalyst. Steam, which is... 

A similar but somewhat less ambitious approach is to carry out dehydrogenation of ethylbenzene and oxidation of the hydrogen product alternately in separate reactors containing different catalysts ... 

The dehydrogenation of the mixture of m- and -ethyltoluenes is similar to that of ethylbenzene, but more dilution steam is required to prevent rapid coking on the catalyst. The recovery and purification of vinyltoluene monomer is considerably more difficult than for styrene owing to the high boiling point and high rate of thermal polymerization of the former and the complexity of the reactor effluent, which contains a large number of by-products. Pressures as low as 2.7 kPa (20 mm Hg) are used to keep distillation temperatures low even in the presence of polymerization inhibitor. The finished vinyltoluene monomer typically has an assay of 99.6%. 

Styrene. Commercial manufacture of this commodity monomer depends on ethylbenzene, which is converted by several means to a low purity styrene, subsequendy distilled to the pure form. A small percentage of styrene is made from the oxidative process, whereby ethylbenzene is oxidized to a hydroperoxide or alcohol and then dehydrated to styrene. A popular commercial route has been the alkylation of benzene to ethylbenzene, with ethylene, after which the cmde ethylbenzene is distilled to give high purity ethylbenzene. The ethylbenzene is direcdy dehydrogenated to styrene monomer in the vapor phase with steam and appropriate catalysts. Most styrene is manufactured by variations of this process. A variety of catalyst systems are used, based on ferric oxide with other components, including potassium salts, which improve the catalytic activity (10). 

All lation. Friedel-Crafts alkylation (qv) of benzene with ethylene or propjiene to produce ethylbenzene [100-41 -4] CgH Q, or isopropylbenzene [98-82-8] (cumene) is readily accompHshed ia the Hquid or vapor phase with various catalysts such as BF (22), aluminum chloride,... 

---