Ethane aromatics from

Fig. 8. Mobil s process for aromatics from ethane (38). Ref. = refrigeration CW = cooling water Stm. = steam.

Ethylene glycol for the synthesis of PET is obfained by air oxidation of ethylene to ethylene oxide (Section 11.8A) followed by hydrolysis to the glycol (Section 11.9A). Ethylene is, in turn, derived entirely from cracking eifher petroleum or ethane derived from natural gas (Section 2.9A). Terephthalic acid is obtained by oxidation of p-xylene, an aromatic hydrocarbon obtained along with benzene and toluene from catalytic cracking and reforming of naphtha and other petroleum fractions (Section 2.9B). 

In a polluted or urban atmosphere, O formation by the CH oxidation mechanism is overshadowed by the oxidation of other VOCs. Seed OH can be produced from reactions 4 and 5, but the photodisassociation of carbonyls and nitrous acid [7782-77-6] HNO2, (formed from the reaction of OH + NO and other reactions) are also important sources of OH ia polluted environments. An imperfect, but useful, measure of the rate of O formation by VOC oxidation is the rate of the initial OH-VOC reaction, shown ia Table 4 relative to the OH-CH rate for some commonly occurring VOCs. Also given are the median VOC concentrations. Shown for comparison are the relative reaction rates for two VOC species that are emitted by vegetation isoprene and a-piuene. In general, internally bonded olefins are the most reactive, followed ia decreasiag order by terminally bonded olefins, multi alkyl aromatics, monoalkyl aromatics, C and higher paraffins, C2—C paraffins, benzene, acetylene, and ethane. 

Natural gas and crude oils are the main sources for hydrocarbon intermediates or secondary raw materials for the production of petrochemicals. From natural gas, ethane and LPG are recovered for use as intermediates in the production of olefins and diolefms. Important chemicals such as methanol and ammonia are also based on methane via synthesis gas. On the other hand, refinery gases from different crude oil processing schemes are important sources for olefins and LPG. Crude oil distillates and residues are precursors for olefins and aromatics via cracking and reforming processes. This chapter reviews the properties of the different hydrocarbon intermediates—paraffins, olefins, diolefms, and aromatics. Petroleum fractions and residues as mixtures of different hydrocarbon classes and hydrocarbon derivatives are discussed separately at the end of the chapter. 

As feedstocks progress from ethane to heavier fractions with lower H/C ratios, the yield of ethylene decreases, and the feed per pound ethylene product ratio increases markedly. Table 3-15 shows yields from steam cracking of different feedstocks, and how the liquid by-products and BTX aromatics increase dramatically with heavier feeds. 

PCBs represent chlorine derivatives of biphenyl, containing from 1 to 10 atoms of chlorine in a molecule that is expressed as 10 different homologues (Figure 2). Having no ethane bridge between the aromatic rings, as opposed to DDT, PCBs are more stable... 

The interaction parameters for binary systems containing water with methane, ethane, propane, n-butane, n-pentane, n-hexane, n-octane, and benzene have been determined using data from the literature. The phase behavior of the paraffin - water systems can be represented very well using the modified procedure. However, the aromatic - water system can not be correlated satisfactorily. Possibly a differetn type of mixing rule will be required for the aromatic - water systems, although this has not as yet been explored. 

When naphtha or gas oil is cracked, imagine the limitless combinations possible. Naphthas are made up of molecules in the C5 to Cio range gas oils from Cio to perhaps C30 or C40. The structures include everything from simple paraffins (aliphacics) to complex polynuclear aromatics, so a-much wider range of possible molecules can form. Ethylene yields.froin..cracking naphtha or gas oil are much smaller than those from ethane or propane, as you can see from Table 5-1- But to compensate the plant operator, a full range of other hydrocarbons is produced as by-products also. 

The most common by-product losses are due to transalkylation, dealkylation, saturation and cracking. Transalkylation results in toluene, trimethylbenzenes, methylethyl benzenes, benzene and ClOAs. These are the best by-products to have, because they are the easiest to react back into C8A in a transalkylation unit (if the aromatics complex is so equipped) without any loss of carbon atoms [59-61]. Dealkylation results in benzene, toluene, methane and ethane. The benzene and toluene are aromatics and represent valuable by-products, but the C1-C6 nonaromatics represent carbons that are lost from the complex as less valuable LPG and fuel gas. 

The main conclusion of this study is that hydrocarbon-based surface geochemical methods can discriminate between productive and non-productive oil and gas reservoir areas. Variables in surface soils that best distinguish productive from non-productive areas are ethane, n-butane and heavy (C24+) aromatic hydrocarbons. Heavy metals (U, Mo, Cd, Hg, Pb) are possibly indirect indicators of hydrocarbon microseepage, but they are more difficult to link with the reservoirs. 

In stick notation we write these reactions as shown in Figure 2-17. We described the steps by which cmde oil is converted into aromatics such as p-xylene previously. Here we discuss the production of ethylene glycol from ethane. 

Bond separation reactions and heats of formation obtained from bond separation energies suffer from two serious problems. The first is that bond types in reactants and products for some types of processes may not actually be the same or even similar . The bond separation reaction for benzene is an obvious example. Here to reactant (benzene) incorporates six equivalent aromatic carbon-carbon bonds, midway between single and double bonds, while the products (three ethanes and three ethylenes) incorporate three distinct carbon-carbon single bonds and three distinct carbon-carbon double bonds. 

One of the most important challenges in the modern chemical industry is represented by the development of new processes aimed at the exploitation of alternative raw materials, in replacement of technologies that make use of building blocks derived from oil (olefins and aromatics). This has led to a scientific activity devoted to the valorization of natural gas components, through catalytic, environmentally benign processes of transformation (1). Examples include the direct exoenthalpic transformation of methane to methanol, DME or formaldehyde, the oxidation of ethane to acetic acid or its oxychlorination to vinyl chloride, the oxidation of propane to acrylic acid or its ammoxidation to acrylonitrile, the oxidation of isobutane to... 

The syntheses of iron isonitrile complexes and the reactions of these complexes are reviewed. Nucleophilic reagents polymerize iron isonitrile complexes, displace the isonitrile ligand from the complex, or are alkylated by the complexes. Nitration, sulfonation, alkylation, and bromina-tion of the aromatic rings in a benzyl isonitrile complex are very rapid and the substituent is introduced mainly in the para position. The cyano group in cyanopentakis(benzyl isonitrile)-iron(ll) bromide exhibits a weak "trans" effect-With formaldehyde in sulfuric acid, benzyl isonitrile complexes yield polymeric compositions. One such composition contains an ethane linkage, suggesting dimerization of the transitory benzyl radicals. Measurements of the conductivities of benzyl isonitrile iron complexes indicate a wide range of A f (1.26 e.v.) and o-o (1023 ohm-1 cm.—1) but no definite relationship between the reactivities of these complexes and their conductivities. 

Tetranuclear aromatic diamines were prepared on the basis of bis-phenols derived from 1,1,1-trichloro-2,2-di-(p-methoxyphenyl)-ethane under the action of pyridine hydrochloride [26, 27]. Interaction of the bis-phenols with two-fold molar amounts of p-nitrochlorobenzene led to the formation of 4,4 -bis(/ -nitrophenoxy [-arylenes, which were reduced to the corresponding 4,4 -bis(/ -aminophenoxy[-arylenes [28] (Scheme 2.11). Similar compounds containing two additional amino groups were prepared by the interaction of 3,3 -dinitro-4,4 -dichlorobenzophenone with two-fold molar amounts of potassium p-nitrophenolate [29] followed by reduction of the tetranitro compounds thus formed [29] (Scheme 2.12). 

---