Elemental analysis of materials

It is supposed to apply this neutron source to nondestmctive evaluation of products using neutron radiography and elemental analysis of materials by detection of capture gamma rays. 

Three techniques involving the use of X-ray emission to obtain quantitative elemental analysis of materials are described in this chapter. They are X-Ray Fluorescence, XRF, Total Reflection X-Ray Fluorescence, TXRF, and Particle-Induced X-Ray Emission, PIXE. XRF and TXRF use laboratory X-ray tubes to excite the emission. PIXE uses high-energy ions from a particle accelerator. 

X-Ray Fluorescence (XRF) is a nondestructive method used for elemental analysis of materials. An X-ray source is used to irradiate the specimen and to cause the elements in the specimen to emit (or fluoresce) their characteristic X rays. A detector s)rstem is used to measure the positions of the fluorescent X-ray peaks for qualitative identiflcation of the elements present, and to measure the intensities of the peaks for quantitative determination of the composition. All elements but low-Z elements—H, He, and Li—can be routinely analyzed by XRF. 

Langer S A, Fuller Jr E R and Carter W C (2001) OOF An Image-Based Finite-Element Analysis of Material Microstructures, Comput Sci Eng 3 15-23. 

Trace-element analysis of metals can give indications of the geographic provenance of the material. Both emission spectroscopy (84) and activation analysis (85) have been used for this purpose. Another tool in provenance studies is the measurement of relative abundances of the lead isotopes (86,87). This technique is not restricted to metals, but can be used on any material that contains lead. Finally, for an object cast around a ceramic core, a sample of the core material can be used for thermoluminescence dating. 

Both the wavelength dispersive and energy dispersive spectrometers are well suited for quaUtative analysis of materials. Each element gives on the average only six emission lines. Because the characteristic x-ray spectra are so simple, the process of allocating atomic numbers to the emission lines is relatively simple and the chance of making a gross error is small. 

Measurements of the characteristic X-ray line spectra of a number of elements were first reported by H. G. J. Moseley in 1913. He found that the square root of the frequency of the various X-ray lines exhibited a linear relationship with the atomic number of the element emitting the lines. This fundamental Moseley law shows that each element has a characteristic X-ray spectrum and that the wavelengths vary in a regular fiishion form one element to another. The wavelengths decrease as the atomic numbers of the elements increase. In addition to the spectra of pure elements, Moseley obtained the spectrum of brass, which showed strong Cu and weak Zn X-ray lines this was the first XRF analysis. The use of XRF for routine spectrochemical analysis of materials was not carried out, however, until the introduction of modern X-ray equipment in the late 1940s. 

Both XRF and EPMA are used for elemental analysis of thin films. XRF uses a nonfocusing X-ray source, while EPMA uses a focusing electron beam to generate fluorescent X rays. XRF gives information over a large area, up to cm in diameter, while EPMA samples small spots, (om in size. An important use of EPMA is in point-to-point analysis of elemental distribution. Microanalysis on a sub- lm scale can be done with electron microscopes. The penetration depth for an X-ray beam is normally in the 10-(om range, while it is around 1 (om for an electron beam. There is, therefore, also a difference in the depth of material analyzed by XRF and EPMA... 

The basic elements and considerations for assay development, validation, and specification assignment are reviewed briefly. Assay development produces a method that requires validation for the analysis and release of materials (bulk or formulated finished product) for use in clinical development. The cumulative analysis of materials and stability considerations is then used to established specifications for internal and regulatory submission. 

Trace Element Analysis of Geological Materials. By Roger D. Reeves and Robert R. Brooks... 

Finite element methods are one of several approximate numerical techniques available for the solution of engineering boundary value problems. Analysis of materials processing operations lead to equations of this type, and finite element methods have a number of advantages in modeling such processes. This document is intended as an overview of this technique, to include examples relevant to polymer processing technology. 

Quevauviller Ph, Maier EA, Vercoutere K, Muntau H, Griepink B (1992a) Certified reference material (CRM 397) for the quality control of trace element analysis of human hair. Fresenius J Anal Chem 343 335-338. 

Applications ICP-MS has become the technique of choice for the determination of elements in a wide range of liquid samples at concentrations in the ng L 1 to [igL-1 range. Typical applications of ICP-MS are multi-element analysis of liquids (even with high solid contents) element speciation by hyphenation to chromatographic techniques continuous on-line gas analysis multi-element trace analysis of polymers and trace analysis in high-purity materials. ICP-MS is routinely used for quality control purposes. 

An analysis of materials on human illness of those people living in zones with varying levels of pesticide contamination permitted us to establish a correlation between the illness and the level of pesticide contamination in elements of the outside environment. 

Vol. 51 Trace Element Analysis of Geological Materials. By Roger D. Reeves and Robert R. Brooks Vol. 52 Chemical Analysis by Microwave Rotational Spectroscopy. By Ravi Varma and Lawrence... 

Elemental analysis of activated carbons made from raw materials of this study under various reaction conditions is presented in Table 3. 

Various reference materials have been described, to help improving the reliability of trace elemental analysis of lead and other heavy elements, for clinical and environmental applications. Such materials include blood10,11, diets, feces, air filters, dust11, foodstuffs12 and biological tissues13. 

---