Kraton® elastomer

In the studies at Lehigh the thermoplastic elastomer Kraton G served as polymer I (see Fig, 1). Styrene and methacrylic acid were dissolved into the Kraton G, and polymerized in situ. 

The tear strength of a representative thermoplastic elastomer, Kraton 1101 (Shell Chemical Company), is quite comparable to that of a well-... 

KRATON Thermoplastic Elastomers bulletins. Shell Chemical Co., Houston, Tex. 

Thermoplastic Elastomers. These represent a whole class of synthetic elastomers, developed siace the 1960s, that ate permanently and reversibly thermoplastic, but behave as cross-linked networks at ambient temperature. One of the first was the triblock copolymer of the polystyrene—polybutadiene—polystyrene type (SheU s Kraton) prepared by anionic polymerization with organoHthium initiator. The stmcture and morphology is shown schematically in Figure 3. The incompatibiHty of the polystyrene and polybutadiene blocks leads to a dispersion of the spherical polystyrene domains (ca 20—30 nm) in the mbbery matrix of polybutadiene. Since each polybutadiene chain is anchored at both ends to a polystyrene domain, a network results. However, at elevated temperatures where the polystyrene softens, the elastomer can be molded like any thermoplastic, yet behaves much like a vulcanized mbber on cooling (see Elastomers, synthetic-thermoplastic elastomers). 

An interesting observation arose with the thermoplastic elastomer styrene/ butadiene (S/B) tri-block copolymer (Kraton ). These are made by anionic... 

Kraton 1107 brand elastomer was from Shell Chemical Co., and it is synthesized by coupling the isoprenyl anion ends of a styrene/isoprene (SI) block copolymer to give styrene/isoprene/styrene (SI IS). Proton NMR analysis indicated 84% (wt.) isoprene and 16% (wt.) styrene. 

The ABA block copolymer of styrene (12.5%)-butadiene (75%)-styrene (12.5%) (Kraton), is a thermoplastic elastomer CTPE) with the multiple repeating units shown below ... 

The development of anionic chemistry over the past 30 years has led to the emergence of new processes and products of Industrial Importance, the most significant being a family of thermoplastic elastomers. These unique elastomers are presently commercialized by Shell Chemical Company as Kratons and by Phillips Chemical Company as Solprenes. Their uniqueness is the result of deliberate design of the polymeric structure and composition. 

The hydrogenation of the centre block of SBS copolymer produced oxidation stable thermoplastic elastomer. This product was commercialized by the Shell Development Company under the trade name of Kraton G. The field of thermoplastic elastomers based on styrene, 1-3-butadiene or isoprene has expanded so much in the last 10 years that the synthetic rubber chemist produced more of these polymers than the market could handle. However, the anionically prepared thermoplastic system is still the leader in this field, since it produced the best TPR s with the best physical properties. These TPR s can accommodate more filler, which reduces the cost. For example, the SBS Kraton type copolymer varies the monomer of the middle block to produce polyisoprene at various combinations, then, followed... 

HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HNS NTO NTO/HMX NTO/HMX NTO/HMX PETN PETN PETN PETN PETN PETN PETN PETN PETN PETN RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX TATB/HMX Cariflex (thermoplastic elastomer) Hydroxy-terminated polybutadiene (polyurethane) Hydroxy-terminated polyester Kraton (block copolymer of styrene and ethylene-butylene) Nylon (polyamide) Polyester resin-styrene Polyethylene Polyurethane Poly(vinyl) alcohol Poly(vinyl) butyral resin Teflon (polytetrafluoroethylene) Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Cariflex (block copolymer of butadiene-styrene) Cariflex (block copolymer of butadiene-styrene) Estane (polyester polyurethane copolymer) Hytemp (thermoplastic elastomer) Butyl rubber with acetyl tributylcitrate Epoxy resin-diethylenetriamine Kraton (block copolymer of styrene and ethylene-butylene) Latex with bis-(2-ethylhexyl adipate) Nylon (polyamide) Polyester and styrene copolymer Poly(ethyl acrylate) with dibutyl phthalate Silicone rubber Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Epoxy ether Exon (polychlorotrifluoroethylene/vinylidine chloride) Hydroxy-terminated polybutadiene (polyurethane) Kel-F (polychlorotrifluoroethylene) Nylon (polyamide) Nylon and aluminium Nitro-fluoroalkyl epoxides Polyacrylate and paraffin Polyamide resin Polyisobutylene/Teflon (polytetrafluoroethylene) Polyester Polystyrene Teflon (polytetrafluoroethylene) Kraton (block copolymer of styrene and ethylene-butylene)... 

Thus, in alkyd, polyester, and epoxy coatings applied to CRS, phosphatized steel, and aluminum, the use of ZAs APG (aminofunctional) and CPG (carboxy-functional) has allowed for the virtual elimination of blister formation and corrosion after 300 h of salt fog exposure. The use of multifunctional ZAs in a Kraton base adhesive has allowed for a 52% increase in T-peel strength on EPDM rubber when compared with the same adhesive containing aminofunctional silane. Incorporation of mercaptofunctional ZA into crosslinkable elastomers has... 

The above thermal analysis studies demonstrated the enhanced thermal stability of POSS materials, and suggested that there is potential to improve the flammability properties of polymers when compounded with these macromers. In a typical example of their application as flame retardants, a U.S. patent39 described the use of preceramic materials, namely, polycarbosilanes (PCS), polysilanes (PS), polysilsesquioxane (PSS) resins, and POSS (structures are shown in Figure 8.6) to improve the flammability properties of thermoplastic polymers such as, polypropylene and thermoplastic elastomers such as Kraton (polystyrene-polybutadiene-polystyrene, SBS) and Pebax (polyether block-polyamide copolymer). 

It is important to appreciate that polymer produced by an anionic chain-growth mechanism can have drastically different properties from one made by a normal free radical reaction. Block copolymers can be synthesized in which each block has different properties. We mentioned in Chapter 4 that Michael Szwdrc of Syracuse University developed this chemistry in the 1950s. Since that time, block copolymers produced by anionic polymerization have been commercialized, such as styrene-isoprene-styrene and styrene-butadiene-styrene triblock copolymers (e.g., Kraton from Shell Chemical Company). They find use as thermoplastic elastomers (TPE), polymers that act as elastomers at normal temperatures but which can be molded like thermoplastics when heated. We will discuss TPEs further in Chapter 7. 

Kraton 101 [Shell], TM for a styrene-butadiene elastomer that requires no vulcanization, while displaying most of the properties of conventional vulcanized polymers. White, free-flowing crumb, readily soluble in a large number of commercially used solvents. 

Obviously, the resistance of these products towards light, oxygen and other chemicals will be much better, and close to that of the corresponding polyolefins. Moreover, the hydrogenation can be stopped at different conversions opening a much broader range of applications conditions. Industrial developments already include successful materials like Kraton G thermoplastic elastomers. 

I, vinylruthenocene, 66, vinylosmocene, and the T)5-(vinylcyclopentadienyl)metal carbonyl monomers in radical-initiated polymerizations summarized in Scheme 1.1 no longer exists for anionically initiated addition polymerizations. Styrene is readily initiated by such anionic species as BuLi and Na1 Naphth. Living anionic styrene homopolymerizations and block copolymerizations have been extensively commercialized for many years (e.g., Kraton thermoplastic elastomers). However, the exceptionally electron-rich vinyl metal-containing monomers 1, 8-18, 24-30, and 66 were never successfully initiated by anionic systems in our laboratory despite many attempts. In these systems, the a-carbocations are very stable, but the a-carbanions are quite unstable. Thus, the addition of an anion to tbe vinyl function of these monomers is unfavorable. 

---