Drug sample preparation

APPLYING THE SQENCE 4.3 Combined Add. Neutral, and Bask Drug Sample Preparation with SPE 112... 

An internal standard method gives more reliable results when elaborate sample preparation is required, as in extraction of a drug substance from biological fluids, or extraction of pesticides and herbicides from soil and plant matter. The addition of internal standard (IS) to the sample and standard acts as a marker to give accurate values of the recovery of the desired compound(s). Since the determination of wt% involves the ratio of the detector responses in the two chromatograms, the injection volume is not critical as in an external standard method. 

Next, reductive amination (step 4 in scheme 1) was exchanged with copper catalyzed palladium coupling (step 2 in scheme 1). Atomic absorption analysis for palladium in RWJ-26240 samples prepared by scheme 2 indicated that the level of palladium was reduced to an acceptable level. This improvement may be due to the two reduction steps subsequent to the use of palladium in scheme 2.177 The final major modification to the reaction scheme was the substitution of NaBH4 for NaBH3CN. The yield of product (60%) was determined by HPLC (Method 2). Reductive alkylation with formalin/NaBH4 afforded a pharmaceutically acceptable drug substance. 

The study concluded that Once wash steps are optimized, samples prepared by solid phase extraction are cleaner than those prepared by protein precipitation. Samples prepared by extraction with a Multi-SPE plate resulted in lower LOQs than samples prepared by solvent precipitation. Drug recoveries were acceptable (>80%) for both the SPE and the solvent precipitation methods. Well-to-well reproducibility of samples was slightly better with extraction with a Multi-SPE plate. Evaporation and reconstitution, while more time-consuming, yield better chromatographic performance, allow analysis of lower concentration samples, and require optimization for good analyte recovery. 

A number of benzodiazepine derivatives were evaluated to probe the selective binding of diazepam to the templated MIP. Samples of 20 and 50 ng of each drug were prepared in 1 mL of toluene. 

The next section describes the utilization of //PLC for different applications of interest in the pharmaceutical industry. The part discusses the instrumentation employed for these applications, followed by the results of detailed characterization studies. The next part focuses on particular applications, highlighting results from the high-throughput characterization of ADMET and physicochemical properties (e.g., solubility, purity, log P, drug release, etc.), separation-based assays (assay development and optimization, real-time enzyme kinetics, evaluation of substrate specificity, etc.), and sample preparation (e.g., high-throughput clean-up of complex samples prior to MS (FIA) analysis). 

Modern spectroscopy plays an important role in pharmaceutical analysis. Historically, spectroscopic techniques such as infrared (IR), nuclear magnetic resonance (NMR), and mass spectrometry (MS) were used primarily for characterization of drug substances and structure elucidation of synthetic impurities and degradation products. Because of the limitation in specificity (spectral and chemical interference) and sensitivity, spectroscopy alone has assumed a much less important role than chromatographic techniques in quantitative analytical applications. However, spectroscopy offers the significant advantages of simple sample preparation and expeditious operation. 

The pharmaceutical industry comprises the largest segment, roughly 15 to 20%, of the infrared (IR) market. Modern mid-infrared instrumentation consists almost exclusively of Fourier transform (FT) instruments. Because of its ability to identify molecular species, FT-IR is routinely used as an identification assay for raw materials, intermediates, drug substances, and excipients. However, the traditional IR sample preparation techniques such as alkali halide disks, mulls, and thin films, are time-consuming and not always adequate for quantitative analysis. 

Because the instability of the N-oxide metabolite, which was subjected to decomposition during sample preparation (solvent evaporation during offline SPE), online SPE LC/MS became the method of choice for the application. Hsieh et al. (2004) built a system with two TFC cartridges and one analytical column, and another system with two TFC cartridges and two analytical columns for GLP quantitative bioanalysis of drug candidates. A Turbo C18 (50 x 1.0 mm, 5 /.mi, Cohesive Technologies), an Xterra MS C18 (30 x 2.0 mm, 2.5 /mi), and a guard column were used. Protein precipitation preceded injection. The cycle times for the two systems were 0.8 and 0.4 min. 

Lant M.S. and Oxford J., 1987. Automated sample preparation online with thermospray high-performance liquid chromatography-mass spectrometry for the determination of drugs in plasma. J Chromatogr A 394 223. 

These methods have been used since the 1970s they usually require little or no sample preparation and are rapid and easy to use. However, immunoassay has two limitations. First, it does not differentiate between active drugs and similar molecules such as metabolites or co-administered drugs.9,11 Thus, cross-reactivity is a common problem. Second, its use is limited to only those drugs for which antibodies are available. 

HPLC has high-throughput capability when it can simultaneously determine multiple drugs and their metabolites or when coupled with a unique monolithic column or sample preparation technique. Some examples are summarized below. 

---