Distorted polymers

A Model of the Short Range Order in Distorted Polymer Structures.54... 

The calculation of the X-ray structure factor of distorted polymer structures should be based on a strategy of where to place approximations. As shown by the literature this is a difficult task. 

K Maximal extension coefficient of a distorted polymer coil... 

Bend distortion (polymer) A bending distortion where the rods of the nematic phase are oriented parallel to the surface. See also Splay distortion (polymer). 

We began this section with an inquiry into how to define the size of a polymer molecule. In addition to the molecular weight or the degree of polymerization, some linear dimension which characterizes the molecule could also be used for this purpose. For purposes of orientation, let us again consider a hydrocarbon molecule stretched out to its full length but without any bond distortion. There are several features to note about this situation ... 

In each of these approaches, imaging is confined to the top of a single polymeric film by adjusting optical absorption. The penetration depth of the silylation agent and the attendant swelling of the polymer film must also be controlled to avoid distortion of the silylated image. Resists of this type are capable of very high resolution (Fig. 37). 

TetrabromobisphenoIA. Tetrabromobisphenol A [79-94-7] (TBBPA) is the largest volume bromiaated flame retardant. TBBPA is prepared by bromination of bisphenol A under a variety of conditions. When the bromination is carried out ia methanol, methyl bromide [74-80-9] is produced as a coproduct (37). If hydrogen peroxide is used to oxidize the hydrogen bromide [10035-10-6] HBr, produced back to bromine, methyl bromide is not coproduced (38). TBBPA is used both as an additive and as a reactive flame retardant. It is used as an additive primarily ia ABS systems, la ABS, TBBPA is probably the largest volume flame retardant used, and because of its relatively low cost is the most cost-effective flame retardant. In ABS it provides high flow and good impact properties. These benefits come at the expense of distortion temperature under load (DTUL) (39). DTUL is a measure of the use temperature of a polymer. TBBPA is more uv stable than decabrom and uv stable ABS resias based oa TBBPA are produced commercially. 

Properties. The crystallinity of FEP polymer is significantly lower than that of PTFE (70 vs 98%). The stmcture resembles that of PTFE, except for a random replacement of a fluorine atom by a perfluoromethyl group (CF ). The crystallinity after processing depends on the rate of cooling the molten polymer. The presence of HFP ia the polymer chain teads to distort the highly crystallized stmcture of the PTFE chaia and results ia a higher amorphous fractioa. 

The first HFIP-based polycarbonate was synthesi2ed from bisphenol AF with a nonfluorkiated aromatic diol (bisphenol A) and phosgene (121,122). Incorporation of about 2—6% of bisphenol AF and bisphenol A polycarbonate improved the dimensional stabkity and heat-distortion properties over bisphenol A homopolycarbonate. Later developments in this area concern the flame-retardant properties of these polymers (123,124). 

Fig. 26. Qualitative compatison of substrate materials for optical disks (187) An = birefringence IS = impact strength BM = bending modulus HDT = heat distortion temperature Met = metallizability WA = water absorption Proc = processibility. The materials are bisphenol A—polycarbonate (BPA-PC), copolymer (20 80) of BPA-PC and trimethylcyclohexane—polycarbonate (TMC-PC), poly(methyl methacrylate) (PMMA), uv-curable cross-linked polymer (uv-DM), cycHc polyolefins (CPO), and, for comparison, glass.

Film or fibers derived from low molecular weight polymer tend to embrittle on immersion ia acetone those based on higher molecular weight polymer (>0.60 dL/g) become opaque, dilated, and elastomeric. When a dilated sample is stretched and dried, it retains orientation and is crystalline, exhibiting enhanced tensile strength. The tensile heat-distortion temperature of the crystalline film is iacreased by about 20°C, and the gas permeabiUty and resistance to solvent attack is iacreased. 

Corrosion attack on the polymer is influenced by permeation rate, as weU as internal stresses or fatigue, that distorts or fractures the resin glass fiber... 

For all three diallyl phthalate isomers, gelation occurs at nearly the same conversion DAP prepolymer contains fewer reactive allyl groups than the other isomeric prepolymers (36). More double bonds are lost by cyclisation in DAP polymerisation, but this does not affect gelation. The heat-distortion temperature of cross-linked DAP polymer is influenced by the initiator chosen and its concentration (37). Heat resistance is increased by electron beam irradiation. 

Quenching. After solution treatment, the product is generally cooled to room temperature at such a rate to retain essentially all of the solute in solution. The central portions of thicker products caimot be cooled at a sufficient rate to prevent extensive precipitation in some alloys. Moreover, some forgings and castings are dehberately cooled slowly to minimize distortion and residual stress produced by differential cooling in different portions of the products. Cold water, either by immersion or by sprays, is the most commonly used cooling medium. Hot water or a solution of a polymer in cold water is used when the highest rates are not desired. Dilute Al—Mg—Si and Al—Mg—Zn extmsions can be effectively solution heat treated by the extmsion process therefore, they may be quenched at the extmsion press by either air or water. 

---