Distillation, staged efficiency

When chemical equilibrium is achieved qiiickly throughout the liquid phase (or can be assumed to exist), the problem becomes one of properly defining the physical and chemical equilibria for the system. It sometimes is possible to design a plate-type absorber by assuming chemical-equilibrium relationships in conjunction with a stage efficiency factor as is done in distillation calculations. Rivas and Prausnitz [Am. Tn.st. Chem. Eng. J., 25, 975 (1979)] have presented an excellent discussion and example of the correct procedures to be followed for systems involving chemical equihbria. 

The actual stage can be a mixing vessel, as in a mixer-settler used for solvent extraction applications, or a plate of a distillation or gas absorption column. In order to allow for non-ideal conditions in which the compositions of the two exit streams do not achieve full equilibrium, an actual number of stages can be related to the number of theoretical stages, via the use of a stage-efficiency factor. 

Sieve plates are used, similar to those used for distillation and absorption. The stage efficiency for sieve plates, expressed in terms the height of an equivalent theoretical stage (HETS), will, typically, range from 1 to 2.5 m. 

It should be emphasized that the overall stage efficiency from Equation 9.61 should only be used to derive a first estimate of the actual number of distillation trays. More elaborate methods are available but are outside the scope of this text. In practice, the stage efficiency varies from component to component, and more accurate calculations require much more information on tray type and geometry and physical properties of the fluids. 

It is important to understand whether there will be two-liquid phases present in the column. If two-liquid phases form in a large part of the column, it can make the column difficult to operate. The formation of two-liquid phases also affects the hydraulic design and mass transfer in the distillation (and hence stage efficiency). If it is possible to avoid the formation of two-liquid phases inside the column, then such behavior should be avoided. Unfortunately, there will be many instances when two-liquid phases on some plates cannot be avoided. The formation of two-liquid phases can also be sensitive to changes in the reflux ratio. 

All of the discussions so far regarding distillation lines, residue curves and distillation boundaries have assumed equilibrium behavior. Real columns do not work at equilibrium, and stage efficiency must be accounted for. Each component will have its own stage efficiency, which means that each composition will deviate from equilibrium behavior differently. This means that if nonequilibrium behavior is taken into account, the shape of the distillation lines, residue curves and distillation... 

E Activation energy of reaction (kJ kmol 3), or entrainer flowrate in azeotropic and extractive distillation (kg-s, kmol s-1), or extract flowrate in liquid-liquid extraction (kg s-1, kmol-s-1), or stage efficiency in separation (-)... 

It is essential to have an efficient condenser during the reflux and distillation stages because the product, trimethylsilylacetylene, is extremely volatile. 

Distillation stage calculations are usually performed with ideal stages, The number of ideal stages required for the separation is divided by the overall column efficiency (Sec, 7,1,1) to obtain the required number of trays. In packed towers, the number of stages in the column is multiplied by the HETP (Height Equivalent of a Theoretical Plate, see Sec. 9.1,2) to obtain the packed height. 

The methods based on the equilibrium stage model have existed for over 30 years and refinements continue, but serious development of nonequilibrium models has begun only recently. These methods are an alternative means to the stage model for predicting column performance. They are expected to make inroads, especially for systems for which stage efficiency prediction is very difficult, such as reactive distillation, chemical absorption, and three-phase distillation. However, their progress into systems where efficiency prediction is well-established is likely to be slower. Their complexity due to the restriction to... 

Murphree-stage efficiency Time for distillation Parameter in Underwood equations... 

Choose materials of construction based on corrosion considerations. Column diameters are determined by specifying linear velocities for the two phases. Column heights are determined by estimating the actual number of stages based on the theoretical stage requirements and average stage efficiency. Internals in pulse columns are very similar to those in distillation towers, especially for sieve trays. Therefore, distillation correlations can be used to estimate FOB purchased and installed costs for continuous differential contactors, if they are assumed to be pulse columns. 

Because — [ln(l — 0)] /0 is greater than unity, the stage efficiency in cross flow exceeds the local efficiency E Eg- A similar result is found in distillation, where the plate efficiency is greater than the point efficiency when there is cross flow of liquid without mixing across the plate. 

Since most continuous extraction methods use countercurrent contacts between two phases, one a light liquid and the other a heavier one, many of the fundamentals of countercurrent gas absorption and of rectification carry over into the study of liquid extraction. Thus questions about ideal stages, stage efficiency, minimum ratio between the two streams, and size of equipment have the same importance in extraction as in distillation. 

---