Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Dissolution concepts

Unlike the thermal processing methods for the consolidation of polymers such as PP, which may use selective fibre surface melting, selective dissolution of cellulose fibres partially dissolves the surface layer of cellulose fibres to form a matrix phase of the all-cellulose composites. Analogous to thermal processing methods described earlier, only the surface of the fibre is intended to be affected by the solvent processing and the core of the fibres maintain their structure in order to provide mechanical reinforcement for the final composite. If performed in a controlled manner, this selective surface dissolution concept can result in a continuous... [Pg.33]

Practical Solubility Concepts. Solution theory can provide a convenient, effective framework for solvent selection and blend formulation (3). When a solute dissolves in a solvent, a change in free energy occurs as a result of solvent—solute interactions. The change in free energy of mixing must be negative for dissolution to occur. In equation 1,... [Pg.264]

The most important outcome of this theory is that the rate of dissolution should be potentially greater as the pH increases, which is in conflict with simple concepts of corrosion kinetics. However, the theory has been proved to be applicable to many systems, and BonhoeflFer and Heusler found that iron in sulphuric acid corroded at a greater rate with increase in pH, whilst Kabanov etal. found that it corroded faster in alkaline solution than in acid solution for the same electrode potential. [Pg.308]

The dissolution of A1C13 in the NaAlCl4 melt makes the melt acidic. The acidic-base concept has been discussed by Blander et al. [40]. An acidic melt influences the solubility of the nickel chloride in the ZEBRA cell the solubility of the nickel chloride increases. [Pg.585]

A 55 X 55 grid is used with 2100 water cells, corresponding to a density of 69%. A number of solute molecules are then added. If 100 solute molecules are used, then this number would be subtracted from the 2100 water molecules to maintain 69% cells in the grid. The assumption is made that the volume of all molecules in the grid is about 69%. This assumes that the dissolution in this study produces an overall expansion of the volume of the system to 3125 occupied cells, but we are modeling only 3025 of these as water cells. Volume expansion on addition of a solute is recognized, but it may not be a universal phenomenon. The reader is invited to explore this concept. [Pg.59]

Different views exist as to the reasons for selective dissolution of the asperities. According to older concepts, convection of the liquid is hindered in the solution layers filling recesses hence, reaction products will accumulate there and raise the concentration and viscosity in these layers. Both factors tend to lower a metal s anodic dissolution rate relative to that at raised points. According to other concepts, a surface condition close to passive arises during electropolishing. In this case, the conditions for passivation of the metal at raised points differ from those in recesses. [Pg.315]

The concepts and basic approach used in studies of electrical fluctuations in corrosion processes proved to be very successful as well in mechanistic studies of electrode reactions taking place at materials covered by passivating films. A typical example is the electrochemical dissolution of silicon. From an analysis of the noise characteristics of this process, it has been possible to identify many features as well as the conductivity of the nanostructures of porous silicon being formed on the original silicon surface. [Pg.628]

It was found that the intensity of Co2ps/2 decreased significantly (by a factor of 2.5), supporting the concept of Co dissolution from the alloy and formation of the Pt skin layer on the electrode surface during electrochemical stabilization. As shown in Fig. 10.4b, a clear CL shift was stUl observed in the Pt4/7/2 spectmm for the stabilized Pt-Co, in spite of the dissolution of Co, although the CL shift after stabilization was slightly smaller (0.15 eV) than in the as-prepared alloy (0.19 eV). Thus, we... [Pg.324]

The fundamental concept of heat transport controlled moisture uptake [17] is shown in Eq. (22), where the rate of heat gained at the solid/vapor surface (W AH) is balanced exactly by the heat flow away from the surface (Q). The term All is the heat generated by unit mass of water condensed on the surface. The two most probable sources of heat generation are the heat of water condensation and the heat of dissolution. A comparison of the heat of water condensation (0.58 cal/mg water) with the heat of dissolution for a number of salts indicates that the heat of dissolution can be neglected with little error for many materials. [Pg.709]

Although, the pH-partition hypothesis has not been found to be universally applicable, it has resulted in the recognition of the important contribution of GI pH to permeability and to the dissolution rate of solid dosage forms. This theory does not consider the solubility of the drug, which is a critical physicochemical parameter in the oral absorption process. Dressman et al. [34] developed an absorption potential concept that takes the two parameters into account. The absorption potential is defined as... [Pg.198]

In vitro dissolution testing is an important tool in the development of solid drug products, as well as in batch quality controls. The aim of the test is to see that the drug is appropriately dissolved in the gastrointestinal tract and made available for absorption. It is therefore highly desirable that the in vitro tests provide data that correlate to the in vivo situation. However, attainment of IVIVC has often failed-and the concept of IVIVC has been challenged. [Pg.520]

When drug polymorphs cannot interconvert as a result of being suspended in aqueous solution, a different bioavailability of the two forms usually results [126], For instance, the peak concentration of chloramphenicol in blood serum was found to be roughly proportional to the percentage of the B-polymorph of chloramphenicol palmitate present in a matrix of the A-polymorph [133]. The same concept has been found to apply to hydrate species, where the higher solubility and dissolution rate of the anhydrous phase relative to the trihydrate phase resulted in measurably higher blood levels when using the anhydrate as... [Pg.367]

In the last two decades, the concept of bioavailability has gained prominence and with it dissolution as a possible in vitro model for drug absorption. In 1960, Swintosky and Blythe199... [Pg.33]


See other pages where Dissolution concepts is mentioned: [Pg.354]    [Pg.1504]    [Pg.395]    [Pg.450]    [Pg.140]    [Pg.1158]    [Pg.1171]    [Pg.222]    [Pg.250]    [Pg.37]    [Pg.409]    [Pg.401]    [Pg.274]    [Pg.275]    [Pg.133]    [Pg.13]    [Pg.309]    [Pg.46]    [Pg.27]    [Pg.43]    [Pg.656]    [Pg.29]    [Pg.126]    [Pg.131]    [Pg.137]    [Pg.160]    [Pg.439]    [Pg.157]    [Pg.421]    [Pg.477]    [Pg.266]    [Pg.12]    [Pg.343]    [Pg.5]    [Pg.37]    [Pg.411]    [Pg.90]   
See also in sourсe #XX -- [ Pg.293 ]




SEARCH



© 2024 chempedia.info