Dielectric modulator

Despa F, Fernandez A, Berry RS (2004) Dielectric modulation of biological water. Phys Rev Lett 93 228104... 

The goal of this section is to describe a semiempirical model of nanoscale solvation that captures the dielectric modulation brought about by the approach of a hydrophobe to a protein hydrogen bond. In essence, the model captures the solvent-ordering effect promoted by the hydrophobe and quantifies the effect of this induced organization on the electrostatics of a pre-formed amide-carbonyl hydrogen bond. This model reproduces the crossover point in hydrogen bond dehydration... 

Dielectric Modulation of Interfacial Water Around Dehydrons... 

Semiconductors (qv) are materials with resistivities between those of conductors and those of insulators (between 10 and 10 H-cm). The electrical properties of a semiconductor determine the hmctional performance of the device. Important electrical properties of semiconductors are resistivity and dielectric constant. The resistivity of a semiconductor can be varied by introducing small amounts of material impurities or dopants. Through proper material doping, electron movement can be precisely controlled, producing hmctions such as rectification, switching, detection, and modulation. 

A substrate is a robust element that provides mechanical support for the die. It can be mounted with more than one die such packages are called multichip modules. Because parasitic capacitance effects are directiy proportional to the dielectric constant, substrate material should have a low dielectric constant. 

Single-crystal sUicon has also been employed as substrate material, particularly in multichip module (MGM)-Si appUcations. As a substrate, sUicon offers good thermal conductivity and matches the GTE of the devices mounted on it it does, however, have a relatively high dielectric constant and is very britde. 

There are two main functions the forward-mode transformer performs the first is to provide a dielectric isolation barrier from the input to the output and the second is to step up or step down the pulsewidth modulated ac input voltage signal. The design flow becomes a step-by-step design procedure. 

Insertion mechanism, 231 Integral skin foams, 205 Integrated circuit modules, dielectrics for, 270-271... 

Ferroelectric materials are capable of being polarized in the presence of an electric field. They may exhibit considerable anomalies in one or more of their physical properties, including piezoelectric and pyroelectric coefficients, dielectric constant, and optoelectronic constant. In the latter case, the transmission of light through the material is affected by the electric field, which produces changes in refractive index and optical absorption coefficient. Varying the applied field changes the phase modulation. 

As we have shown, the polarization force depends not only on the topography [through the f(R z) term] and dielectric constant e, but also on the local contact potential 4). As we shall see now, ac bias modulation and lock-in detection allow these contributions to be separated. 

Lead(II) sulfide occurs widely as the black opaque mineral galena, which is the principal ore of lead. The bulk material has a band gap of 0.41 eV, and it is used as a Pb " ion-selective sensor and IR detector. PbS may become suitable for optoelectronic applications upon tailoring its band gap by alloying with II-VI compounds like ZnS or CdS. Importantly, PbS allows strong size-quantization effects due to a high dielectric constant and small effective mass of electrons and holes. It is considered that its band gap energy should be easily modulated from the bulk value to a few electron volts, solely by changing the material s dimensionality. 

Liquid voltaic cells are systems composed of conducting, condensed phases in series, with a thin gap containing gas or liquid dielectric (e.g., decane) situated between two condensed phases. The liquid voltaic cells contain at least one liquid surface [2,15], Due to the presence of a dielectric, special techniques for the investigation of voltaic cells are necessary. Usually, it is the dynamic condenser method, named also the vibrating plate method, the vibrating condenser method, or Kelvin-Zisman probe. In this method, the capacity of the condenser created by the investigated surface and the plate (vibrating plate), is continuously modulated by periodical vibration of the plate. The a.c. output is then amplified, and fed back to the condenser to obtain null-balance operation [49,50]. 

---