Density, effective

Fig. 11) form very strong and selective complexes with Fe or actinide and lanthanide ions (63,64) while a similar receptor with hard endocarboxyhc acid groups is efficient for hard and ions showing again responsibility of a charge density effect in the receptor—substrate recognition (65). Thus,... 

Figure 18 is an entrainment or gas-carryiag capacity chart (25). The operating conditions and particle properties determine the vertical axis the entrainment is read off the dimensionless horizontal axis. For entrainment purposes, the particle density effect is considered through the ratio of the particle density to the density of water. When the entrainable particle-size distribution is smaller than the particle-size distribution of the bed, the entrainment is reduced by the fraction entrainable, ie, the calculated entrainment rate from Figure 18 is multipfled by the weight fraction entrainable. 

Attachment site density effects in inorganic primer films... 

A correction factor, R, incorporating both viscosity and density effects can be developed for a given slurry, which provides a more convenient expression based on the following equation ... 

F. Finaish, R. George, H. J. Sauer. Experimental study of tempetature, ptessure, humidity and/ or density effects on vane anemometers. ASHRAE Transactions, 101 (2), 1995, pp. 240-25 1. 

Abnormal Formation Pressures Origin. Four main causes are attributed to abnormal formation pressures compaction effects, diagenetic effects, differential density effects and fluid migration. 

The differential density effects are especially related to thick gas reservoirs or highly dipping reservoirs. If we assume that at the gas/water contact a normal pressure exists, as we come up the reservoir or updip, the normal pressure due to the water column decreases more rapidly than the gas pressure. 

Density effect If a 40 g package were to be designed according to Fig. 8-53 using a 6.0 pcf foam, the foam would measure 3 in. thick at a loading of about 1.35 psi. If an identical package were then produced using a 2.2 pcf foam, its shock performance would not go as... 

Fig 9 Density effect of stretched and unstretched explosives curves 1—3 refer to unstressed sheets 1 = 15% natural rubber, 2 = 15% depolymerized rubber, 3 = 20% depolymerized rubber. Curve 4 refers to a stretched 15% rubber containing explosive of 1,4g/cc initial density (Ref 45)... 

Apparently, annealing was not impeded by crosslinks (Fig. 5.1). The density effects observed agree with the results of the glass transition temperature measurements (Sect. 4.2). There, the Tg of the annealed (and therefore denser) sample was consistently higher by about 2 K than the Tg of the quenched polymer. 

Effects of current density(I) on the recovery of copper in the reactor can be seen in Fig. 5. As can be seen, the value of R increased gradually with increasing ciurent density, since the mass transfer rate of copper ion is proportional to the current density. Effects of amount of fluidized particles on the recovery of copper can be seen in Fig. 6. Note that the addition of a small amount of fluidized particles (W=1.0wt.%) to the reactor could increase the copper recovery up to 10 25%. It has been mderstood that the contacting of fluidized solid particles with the cathode plate could clean the siuface as well as decrease the diffusion layer of copper ion, which results in the increases of reaction rate and current efficiency, thus, the recovery of copper could be increased. 

This situation is one involving both a total and a component mass balance, combined with a kinetic equation for the rate of decomposition of the waste component. Neglecting density effects, the total mass balance equation is... 

These equations complete a preliminary model for the mixer. Note that it is also possible, in principle, to incorporate changing density effects into the total mass balance equation, provided additional data, relating liquid density to concentration are available. 

To model the amidation and cyclization reactions, an internal standard was weighed into the feed, and the feed placed on a balance for continuous weighing during the reaction. The HPLC system was calibrated using units of mol/kg, so that density effects could be neglected. A series of experiments... 

Inertial impaction is the method of choice for evaluating particle or droplet size delivery from pharmaceutical aerosol systems. This method lends itself readily to theoretical analysis, ft has been evaluated in general terms [39] and for specific impactors [40]. Inertial impaction employs Stokes law to determine aerodynamic diameter of particles being evaluated. This has the advantage of incorporating shape and density effects into a single term. 

Soil density effect on root growth and water use Y N N N... 

Blumenkrantz and Taborek (1971) applied the density effect model of Boure to predict instability in natural-circulation systems in thermosiphon reboil-ers used in the petrochemical industry. An important conclusion of their work was that similarity analysis in terms of the model s dimensionless groups can be used to extrapolate threshold stability data from one fluid to another. 

The shift factor b, shows a large deviation from a simple density effect, it would be expected that the values would not vary far from unity [44], One possible explanation is an internal structure development occurring in PLANCs during measurement (shear process). The alignment of the silicate layers probably enables the PLFNC melts to withstand the shear force, thus leading to the increase in the absolute values of G (co) and G"(co). 

At moderate energies, the electron can acquire relativistic speeds. Including this effect as well as corrections due to shell and density effects, the electron stopping number may be written as... 

Electron-density effects on fi-decay lifetimes also enable the total density to be placed in the range 2500 to 13 000 gm cm-3 all these parameters are characteristic of helium shell-burning zones as expected. 

Steward (1964) [4] and (1970) [5] presented a rigorous but implicit approximate analysis for both axisymmetric and two-dimensional strip fire plumes respectively, including combustion and variable density effects. 

Up to densities of about 0.001 fm-3 density effects can be neglected. This way we describe an ideal mixture in chemical equilibrium. The composition as well as the thermodynamical functions can be calculated immediately... 

This set of parameters is chosen in order to reproduce the binding energy of the deuteron as well as of the alpha particle. The further properties, as the wave functions are assumed to be reasonable approximations in evaluating the density effects. 

COLOR SUPERCONDUCTIVITY AND HIGH DENSITY EFFECTIVE THEORY... 

At low temperature or energy, most degrees of freedom of quark matter are irrelevant due to Pauli blocking. Only quasi-quarks near the Fermi surface are excited. Therefore, relevant modes for quark matter are quasi-quarks near the Fermi surface and the physical properties of quark matter like the symmetry of the ground state are determined by those modes. High density effective theory (HDET) [7, 8] of QCD is an effective theory for such modes to describe the low-energy dynamics of quark matter. 

Color superconductivity and high density effective theory... 

---