Cure agents/accelerators

Curing Agents Accelerators Activators Antidegradants Plasticizers Fillers Pigments... [Pg.505]

Novel, toughened one-component epoxy structural adhesives based on epoxy-terminated polyurethane prepolymer incorporating an oxolidone structure were developed to provide improved toughness, fracture resistance and adhesive properties with good chemical and moisture resistance.21 The hybrid resin cures with a standard latent curing agent/accelerator. [Pg.133]

An ultraviolet (UV) spectrum of an aqueous rubber extract identifies and quantifies the antioxidants, curing agents, accelerators, and other UV-absorbing species extracted from the compound. [Pg.1474]

Accelerators (promoters) are substances which hasten a reaction, usually by acting in conjunction with a catalyst or a curing agent. Accelerators are sometimes used in the polymerization of thermoplastics, but are used most widely in curing systems for thermosets and natural and synthetic rubbers. Accelerators are sometimes called cocatalysts (1). [Pg.293]

Zeonet [Zeon] Curing agent, accelerator, retarder for rubbers. [Pg.413]

Anchor. [Pacific Anchw] Epoxy curing agents, accelerators, antioxidants for rubber, plastics, latc , cements, adhesives, carpet ba ngs, footwear, cable insulatkm, mechanical goods pq>tizer. [Pg.26]

Resicure. [AtochemN. Am.] Qioxy resins, curing agents, accelerates. [Pg.311]

PHENOLIC-TYPE CURING AGENT ACCELERATED WITH 0.45 PHR METHYL-IMIDAZOLE AND CONTAINING 67 WT. % SILICA FLOUR AND 5 PHR MONTAN WAX... [Pg.148]

Curing agent % Accelerator % Gelation time (min) Demolding time (min)... [Pg.557]

Chem. Descrip. 2,4,6-Tii (dimethylaminomethyl) phenol CAS 90-72-2 EINECS/ELINCS 202-013-9 Uses Epoxy curing agent, accelerator for mercaptan-cured epoxies, low-temp. acceleration of polyamides, amido-amines, civil engineering applies. [Pg.160]

The principal manufacturing process includes the moulding of reinforcements and the resin mix into the desired shape. In addition to manual processes, there are many partly or totally closed procedures in which the workers exposure to matrix or reinforcing material is of short duration. Before the moulding, resins are formulated by mixing the basic resin with solvents, curing agents, accelerators, fillers, mould... [Pg.611]

Most workers are involved in the preliminary treatment of moulds with a release agent and in the formulation of resins by mixing the basic resin with solvent, curing agent, accelerator, filler, colour and... [Pg.845]

Uses stabilizer in steroid creams and rubber latex inhibitor in antifreeze solutions and cooling fluids in floor-polish remover in nystatin cream and aminophylline epoxy-curing agent accelerator in color development baths in photography in veterinary preparations in electroplating and electrophoretic gels, dyes, fungicides, insecticides, synthetic waxes, textile lubricants, and eye and nose drops solvent for casein, albumin, shellac... [Pg.1213]

If the rate of polysulfide oligomer curing is to be lowered, numerous procedures may be applied. One of these requires the substitution for a part of Pb02 with PbO. The same effect is produced by the introduction into the system of oleic or stearic acids. The efficiency of these agents decreases with medium humidity and during use. Yet some curing agent-accelerator-inhibitor combinations are preferred (Table 7). [Pg.480]

Table 7 Curing Agent-Accelerator-Retarder Systems...

Fast curing (i.e., short open time) Curing agent Accelerator... [Pg.26]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...