Corrosion features effect

IRB and Their Corrosion-Decelerating Effect A very interesting feature related to IRB is that under certain conditions, they can actually decelerate corrosion instead of accelerating it. This feature of IRB, while it is certainly worthwhile to be noticed for research, may not appear to be that useful from an industrial application point of view. 

Features Improves thickener performance, imparts exc. pH stability, reduces corrosion problems effective in low-odor systems replacement for ammonia... 

Features Effective against both CO2 and H2S corrosion readiiy compat, with other water treating cationics and nonionics... 

Because systems are normally not designed for use with this type of fluid, certain aspects should be reviewed with the equipment and fluid suppliers before a decision to use such fluids can be taken. These are compatibility with filters, seals, gaskets, hoses, paints and any non-ferrous metals used in the equipment. Condensation corrosion effect on ferrous metals, fluid-mixing equipment needed, control of microbial infection together with overall maintaining and control of fluid dilution and the disposal of waste fluid must also be considered. Provided such attention is paid to these designs and operating features, the cost reductions have proved very beneficial to the overall plant cost effectiveness. 

The effective use of metals as materials of construction must be based on an understanding of their physical, mechanical and chemical properties. These last, as pointed out earlier, cannot be divorced from the environmental conditions prevailing. Any fundamental approach to the phenomena of corrosion must therefore involve consideration of the structural features of the metal, the nature of the environment and the reactions that occur at the metal/environment interface. The more important factors involved may be summarised as follows ... 

Finally, it should be noted that in both cases the effect of crystal defects and microstructural features must, in general, be to tend to make the corrosion less uniform and more localised. 

Note that Reference" draws attention to the possibility of an increase of anodic polarisation of the more negative member of a couple leading to a decrease in galvanic corrosion rate. There can also be a risk of increased corrosion of the more positive member of a couple. Both these features can arise as a result of active/passive transition effects on certain metals in certain environments. 

One of the main factors which establishes the corrosivity of water to stainless steel is the chloride content. Also significant are oxygen content and pH, and it is also probable that other features such as hardness and the nature and concentration of other anions and cations have effects. Water temperature and flow velocity can also be important. Any corrosion takes the form of pitting or, if crevices are available, larger areas of attack within the crevice. 

The effect of environmental variables upon the logarithm of velocity V5. K relationship has been examined for a few alloys in some conditions of heat treatment. While it cannot be certain that similar results would be obtained with all alloys, the results reported do show interesting features that may have points in common with all alloys. For an Al-Zn-Mg-Cu alloy (7075-T651) the stress-corrosion plateau velocity was a maximum in 5 m KI solution under potentiostatic conditions at -520 mV (v5. S.C.E.), reaching about 2 X 10 to 5 X 10 cm/s, whereas in 3% NaCl under open-circuit... 

It will be seen that the design of articles to be electroplated can have a considerable effect on the corrosion resistance of the electrodeposited coating. The chief effects are the result of variations in deposit thickness, but also important are features which can influence the adhesion, porosity and physical properties of the deposit. Good design will also avoid features of the plated article capable of trapping liquids or solid contaminants which might cause more rapid corrosion. 

Impure metals and alloys exhibit all the structural features and crystal defects of the pure meteils already discussed. In addition, however, impure metals and alloys exhibit many structures which are not observed in pure metals, and which, in many instances, have an extremely important effect on the properties, particularly the corrosion resistance. However, before dealing with the structure of impure metals and alloys, it is necessary to consider the concept of metallurgical components, phases, constituents and equilibrium phase diagrams. 

The most striking results were obtained with aehromatedZn-Fe alloy (0.3% Fe). It was confirmed that the particularly good corrosion resistance of this alloy is due to the properties of the chromating layer,which remained firmly attached to the metal surface until nearly all of the zinc alloy had been dissolved. This feature rules out chunk effects, so that a shift in the ratio of EC to CMT measurements from a little less than one to one half (over a long time and accompanied by an increase in corrosion potential by 120 mV) could best be explained as a result of a shift in... 

Adhesives and sealers can be an important part of a total corrosion protection system. Structural bonding procedures and adhesives for aluminum, polymer composites, and titanium are well established in the aerospace industry. Structural bonding of steel is gaining increasing prominence in the appliance and automotive industries. The durability of adhesive bonds has been discussed by a number of authors (see, e.g., 85). The effects of aggressive environments on adhesive bonds are of particular concern. Minford ( ) has presented a comparative evaluation of aluminum joints in salt water exposure Smith ( ) has discussed steel-epoxy bond endurance under hydrothermal stress Drain et al. (8 ) and Dodiuk et al. (8 ) have presented results on the effects of water on performance of various adhesive/substrate combinations. In this volume, the durability of adhesive bonds in the presence of water and in corrosive environments is discussed by Matienzo et al., Gosselin, and Holubka et al. The effects of aggressive environments on adhesively bonded steel structures have a number of features in common with their effects on coated steel, but the mechanical requirements placed on adhesive bonds add an additional level of complication. 

---