Complex dynamics shear modulus

In the initial selection of an acoustic absorbing material for an underwater application, the first considerations are often the density, and the complex dynamic shear modulus. These quantities can be measured in the laboratory,requiring only small sample sizes and hence are useful as a guide to material development. 

During a temperature cycle, emulsion stability can be evaluated using dynamic mechanical analysis (DMA) by means of viscosity measurements. Here, the sample is exposed to a small shear deformation with fixed amplitude and frequency and the complex dynamic shear modulus G = G - - G" is determined. G characterizes the elastic properties and G" the viscous properties of the material. A change in the modulus from cycle to cycle indicates structural changes induced by the applied thermal stresses [12,13]. 

Reinforced vulcanized samples generally present a marked viscoelastic behavior that is usually studied by dynamic viscoelastic measurements. In this experiment, a sample is subjected to periodic sinusoidal shear strain y (at defined frequency (o and temperature T). Its dynamic shear modulus G is complex and can be written as the sum of the storage modulus G, and the loss modulus G". 

A viscoelastic material also possesses a complex dynamic viscosity, rj = rj - - iv( and it can be shown that r = G jiuj-, rj = G juj and rj = G ju), where CO is the angular frequency. The parameter Tj is useful for many viscoelastic fluids in that a plot of its absolute value Tj vs angular frequency in radians/s is often numerically similar to a plot of shear viscosity Tj vs shear rate. This correspondence is known as the Cox-Merz empirical relationship. The parameter Tj is called the dynamic viscosity and is related to G the loss modulus the parameter Tj does not deal with viscosity, but is a measure of elasticity. 

Like any dynamic strain instrument, the RPA readily measures a complex torque, S (see Figure 30.1) that gives the complex (shear) modulus G when multiplied by a shape factor B = iTrR / ia, where R is the radius of the cavity and a the angle between the two conical dies. The error imparted by the closure of the test cavity (i.e., the sample s periphery is neither free nor spherical) is negligible for Newtonian fluids and of the order of maximum 10% in the case of viscoelastic systems, as demonstrated through numerical simulation of the actual test cavity." ... 

Contrary to the phase separation curve, the sol/gel transition is very sensitive to the temperature more cations are required to get a gel phase when the temperature increases and thus the extension of the gel phase decreases [8]. The sol/gel transition as determined above is well reproducible but overestimates the real amount of cation at the transition. Gelation is a transition from liquid to solid during which the polymeric systems suffers dramatic modifications on their macroscopic viscoelastic behavior. The whole phenomenon can be thus followed by the evolution of the mechanical properties through dynamic experiments. The behaviour of the complex shear modulus G (o)) reflects the distribution of the relaxation time of the growing clusters. At the gel point the broad distribution of... 

Dynamic mechanical results are generally given in terms of complex moduli or compliances (3,4), The notation will be illustrated in terms Of shear modulus G, but exactly analogous notation holds for Young s modulus F. The complex moduli are defined by... 

The Weissenbeig Rheogoniometer (49) is a complex dynamic viscometer that can measure elastic behavior as well as viscosity. It was the first rheometer designed to measure both shear and normal stresses and can be used for complete characterization of viscoelastic materials. Its capabilities include measurement of steady-state rotational shear within a viscosity range of 10-1 —13 mPa-s at shear rates of 10-4 — 104 s-1, of normal forces (elastic effect) exhibited by the material being sheared, and of an oscillatory shear range of 5 x 10-6 to 50 Hz, from which the elastic modulus and dynamic viscosity can be determined. A unique feature is its ability to superimpose oscillation on steady shear to provide dynamic measurements under flow conditions all measurements can be made over a wide range of temperatures (—50 to 400°C). 

Rheological properties of filled polymers can be characterised by the same parameters as any fluid medium, including shear viscosity and its interdependence with applied shear stress and shear rate elongational viscosity under conditions of uniaxial extension and real and imaginary components of a complex dynamic modulus which depend on applied frequency [1]. The presence of fillers in viscoelastic polymers is generally considered to reduce melt elasticity and hence influence dependent phenomena such as die swell [2]. 

The dynamic mechanical measurements were performed with a Rheometrics IV apparatus in a geometrical arrangement of parallel plates. The complex shear modulus G (= G + fG", where G and G", respectively, are the storage and loss moduli) at a constant frequency of 1 Hz was determined [30]. 

The evolution of the dynamic viscosity rp (co, x) or of the dynamic shear complex modulus G (co.x) as a function of conversion, x, can be followed by dynamic mechanical measurements using oscillatory shear deformation between two parallel plates at constant angular frequency, co = 2irf (f = frequency in Hz). In addition, the frequency sweep at certain time intervals during a slow reaction (x constant) allows determination of the frequency dependence of elastic quantities at the particular conversion. During such experiments, storage G (co), and loss G"(co) shear moduli and their ratio, the loss factor tan8(co), are obtained ... 

We note that, in principle, the main physical discussions related to filler networking in this paper do not change if a sinusoidal tensile or uniaxial compres-sional stress (amplitude 0) is imposed on the rubber material. In some examples the complex dynamic modulus is then denoted with E = E + iE" and the compliance with C = C - iC". All theoretical considerations use the shearing modulus G. ... 

This section examines the dynamic behavior and the electrical response of a TSM resonator coated with a viscoelastic film. The elastic properties of viscoelastic materials must be described by a complex modulus. For example, the shear modulus is represented by G = G + yG", where G is the storage modulus and G" the loss modulus. Polymers are viscoelastic materials that are important for sensor applications. As described in Chapter S, polymer films are commmily aj lied as sorbent layers in gas- and liquid-sensing applications. Thus, it is important to understand how polymer-coated TSM resonators respond. 

A particularly useful expression for the complex dynamic moduli was introduced using operators and fractional derivatives for the viscoelastic constitutive equations ( ). For a rheologically simple system the complex shear modulus is... 

From dynamic experiments and applying the time temperature superposition principle, the complex shear modulus is measured over about five decades and the Rouse model can be checked extensively [37]. 

---