Coatings barrier properties

The value of RN depends on the bandwidth of the ECN measurement and equals the - polarization resistance (RP) only if the ECN and impedance data are independent of frequency within that bandwidth. In such cases, Rn can be used to compute the corrosion rate of a bare metal specimen [i, ii]. For coated metals, the Rn is often used as a measure of coating barrier properties [iii]. 

Some cast (unoriented) polypropylene film is produced. Its clarity and heat sealabiUty make it ideal for textile packaging and overwrap. The use of copolymers with ethylene improves low temperature impact, which is the primary problem with unoriented PP film. Orientation improves the clarity and stiffness of polypropylene film, and dramatically increases low temperature impact strength. BOPP film, however, is not readily heat-sealed and so is coextmded or coated with resins with lower melting points than the polypropylene shrinkage temperature. These layers may also provide improved barrier properties. 

Poly(vinyhdene chloride) (PVDC) film has exceUent barrier properties, among the best of the common films (see Barrier polymers). It is formulated and processed into a flexible film with cling and tacky properties that make it a useful wrap for leftovers and other household uses. As a component in coatings or laminates it provides barrier properties to other film stmctures. The vinyUdene chloride is copolymerized with vinyl chloride, alkyl acrylates, and acrylonitrile to get the optimum processibUity and end use properties (see Vinylidene chloride monomer and polymers). 

Polyester. Poly(ethylene terephthalate) [25038-59-9] (PET) polyester film has intermediate gas- and water- vapor barrier properties, very high tensile and impact strengths, and high temperature resistance (see Polyesters, thermoplastic). AppHcations include use as an outer web in laminations to protect aluminum foil. It is coated with PVDC to function as the flat or sealing web for vacuum/gas flush packaged processed meat, cheese, or fresh pasta. 

Nylon films are used in lamination or coated form to ensure heat sealabiHty and enhance barrier properties. The largest uses are as thermoforming webs for twin-web processed meat and cheese packagiag under vacuum or in an inert atmosphere. Other uses include bags for red meat, boil-ia-bags, bag-in-box for wine, and as the outer protective layer for aluminum foil in cookie and vacuum coffee packages. 

Plasma processing technologies ate used for surface treatments and coatings for plastics, elastomers, glasses, metals, ceramics, etc. Such treatments provide better wear characteristics, thermal stability, color, controlled electrical properties, lubricity, abrasion resistance, barrier properties, adhesion promotion, wettability, blood compatibility, and controlled light transmissivity. 

Layered Structures. Whenever a barrier polymer lacks the necessary mechanical properties for an appHcation or the barrier would be adequate with only a small amount of the more expensive barrier polymer, a multilayer stmcture via coextmsion or lamination is appropriate. Whenever the barrier polymer is difficult to melt process or a particular traditional substrate such as paper or cellophane [9005-81-6] is necessary, a coating either from latex or a solvent is appropriate. A layered stmcture uses the barrier polymer most efficiently since permeation must occur through the barrier polymer and not around the barrier polymer. No short cuts are allowed for a permeant. The barrier properties of these stmctures are described by the permeance which is described in equation 16 where and L are the permeabiUties and thicknesses of the layers. 

In order to reduce the tendency of the film to shrink oriented film may be annealed at about 100°C whilst under tension immediately after drawing. The film is often coated with another polymer sueh as a vinylidene ehloride-based copolymer. This both improves the barrier properties and improves the heat scalability. 

Rigid PVC is currently the most widely used forming film because of its ideal thermoforming characteristics. A typical thickness before thermoforming is 250 pm (10 mil). PVC does not provide a good barrier for moisture-sensitive products. When better barrier properties are required in a thermoformable blister, PVC is laminated or coated with other materials. Because of environmental issues, other materials such as PP compete for blister usage with PVC. In the medical device industry it has been completely replaced by materials such as PET. 

---