Coating Drying time

Besides the solvent composition, the vehicle system is responsible for various drying deficiencies associated with water-borne coatings, such as slow initial dry time, loss of dry, poor through drying, and hardness (see Coatings). 

Loss of Dry. When the initial dry time of a solvent-based coating becomes substantially longer after aging, it is said to lose dry. The primary cause of this problem has been identified as adsorption of the drier on the pigment surface. Pigments with large surface areas are the worst offenders. 

For the above polyol blend viscosity (Brookfield, ASTM D-2196) = 1500 mPa-S at 23° C. For the reaction mixture working (pot) life 20 min Gardner circular dry times [72°F, 54% relative humidity (RH)] surface dry = 1.0 h, hard dry = 2.0 h, mar free = 3.5 h. For the finished coating gloss (ASTM D-523) = 90+ at 60° impact (ASTM D-2794) = 60 in.-lb direct, 10 in.-lb reverse Tabor abrasion (ASTMD-4060,1000 g load, 1000cycles, CS-17 wheel) = 95.6 mg pendulum hardness = 180 s MEK double rubs (ASTM D4752-95, 50 double rubs) = softened. 

The slurry process has been enhanced with vacuum to fabricate planar SOFCs [78], This method is of low cost and thus has been widely used to develop low-cost SOFCs. However, together with other liquid precursor methods such as sol-gel and spray pyrolysis, it is time, labor, and energy intensive because the coating-drying-sintering has to be repeated in order to avoid cracking formation. 

Fig.12. Comparison between a conventional high solid alkyd coating ( ) and an alkyd based on a hyperbranched aliphatic polyester ( ). Drying time as a function of molar mass [123]...

Pettersson and Sorensen have described a number of different thermoset resin structures based on hyperbranched aliphatic polyesters [123]. Their results can best be exemplified by a study on hyperbranched alkyd coating resins. A comparative study was performed between an alkyd resin based on a hyperbranched aliphatic polyester and a conventional high solid alkyd, which is a less branched structure. The hyperbranched resin had a substantially lower viscosity than the conventional resin of comparable molecular weight, that is, less solvent was needed to obtain a suitable application viscosity. The hyperbranched resin also exhibited much shorter drying times than the conventional resin, although the oil content was similar. These achievements would not have been possible without a change in architecture of the backbone structure of the resins (Figs. 12,13). 

Mastics are sprayed on a substrate in one or more coats, depending on the desired degree of fire resistance. The final coat of all fireproofing mastics should be rolled or brushed to provide a smooth surface finish. The material should be applied with a sufficient number of coats to prevent running or slumping and sufficient drying time should be allowed between coats. Mastics may also be hand-troweled, if permitted in the manufacturer s specifications. 

MCC and carrageenan LustreClear FMC BioPolymer, Newark, Delaware, U.S.A. Efficient tablet-coating with short hydration time prior to coating and fast drying time... 

Spray time for 448 g suspension Drying time after coating (45 °C). 

Figure 4 shows the insulative ability of the above formulation. Three coats were applied over a primer to a total dry film thickness of 20 mils, allowing 24 hours dry time between coats. This graph indicates complete failure in 8 minutes. When subjected to other tests the coating lacked adhesion to metal, moisture resistance, and flexibility. After, puffing, the coating disintegrated under vibration. 

In fact the ideal paint for a particular type of work may not be available, and that selected may represent a compromise between needs such as the use of suitable solvents, the temperatures of processing and curing, and the speed of evaporation ( drying times ) necessary, especially if several coats are to be used. 

---