Chromium alcohols

By passing the alcohol vapour over a copper - chromium oxide catalyst deposit on pumice and heated to 330°, for example ... 

Trimethylene dibromide (Section 111,35) is easily prepared from commercial trimethj lene glycol, whilst hexamethylene dibromide (1 O dibromohexane) is obtained by the red P - Br reaction upon the glycol 1 6-hexanediol is prepared by the reduction of diethyl adipate (sodium and alcohol lithium aluminium hydride or copper-chromium oxide and hydrogen under pressure). Penta-methylene dibromide (1 5-dibromopentane) is readily produced by the red P-Brj method from the commercially available 1 5 pentanediol or tetra-hydropyran (Section 111,37). Pentamethylene dibromide is also formed by the action of phosphorus pentabromide upon benzoyl piperidine (I) (from benzoyl chloride and piperidine) ... 

Equip a I litre three-necked flask with a mechanical stirrer and a thermometer, and immerse the flask in a bath of ice and salt. Place 306 g. (283 ml.) of acetic anhydride, 300 g. (285 ml.) of glacial acetic acid and 25 g. of p-nitrotoluene in the flask, and add slowly, with stirring, 42 5 ml. of concentrated sulphuric acid. When the temperature has fallen to 5°, introduce 50 g. of A.R. chromic anhydride in small portions at such a rate that the temperature does not rise above 10° continue the stirring for 10 minutes after all the chromium trioxide has been added. Pour the contents of the flask into a 3 litre beaker two-thirds filled with crushed ice and almost fill the beaker with cold water. Filter the solid at the pump and wash it with cold water until the washings are colourless. Suspend the product in 250 ml. of cold 2 per cent, sodium carbonate solution and stir mechanically for 10-15 minutes filter (1), wash with cold water, and finally with 10 ml. of alcohol. Dry in a vacuum desiccator the yield of crude p-nitrobenzal diacetate is 26 g. (2),... 

Hydrogenations with coppcr-chromium oxide catalyst are usually carried out in the liquid phase in stainless steel autoclaves at pressures up to 5000-6000 lb. per square inch. A solvent is not usually necessary for hydrogenation of an ester at 250° since the original ester and the alcohol or glycol produced serve as the reaction medium. However, when dealing with small quantities and also at temperatures below 200° a solvent is desirable this may be methyl alcohol, ethyi alcohol, dioxan or methylcyc/ohexane. 

Tertiary alcohols are usually degraded unselectively by strong oxidants. Anhydrous chromium trioxide leads to oxidative ring opening of tertiary cycloalkanols (L.F. Fieser, 1948). 

Vigorous oxidation leads to the formation of a carboxylic acid but a number of meth ods permit us to stop the oxidation at the intermediate aldehyde stage The reagents most commonly used for oxidizing alcohols are based on high oxidation state transition met als particularly chromium(VI)... 

Hydrogen peroxide Copper, chromium, iron, most metals or their salts, alcohols, acetone, organic materials, flammable liquids, combustible materials... 

C and 19,600 kPa (2800 psi). The catalyst is a complex aluminum—ca dmium —chromium oxide that has high activity and exceptionally long life. The process is claimed to give a conversion of ester to alcohol of about 99% retaining essentially all of the original double bonds. 

Usually, organoboranes are sensitive to oxygen. Simple trialkylboranes are spontaneously flammable in contact with air. Nevertheless, under carefully controlled conditions the reaction of organoboranes with oxygen can be used for the preparation of alcohols or alkyl hydroperoxides (228,229). Aldehydes are produced by oxidation of primary alkylboranes with pyridinium chi orochrom ate (188). Chromic acid at pH < 3 transforms secondary alkyl and cycloalkylboranes into ketones pyridinium chi orochrom ate can also be used (230,231). A convenient procedure for the direct conversion of terminal alkenes into carboxyUc acids employs hydroboration with dibromoborane—dimethyl sulfide and oxidation of the intermediate alkyldibromoborane with chromium trioxide in 90% aqueous acetic acid (232,233). 

Chromium compounds decompose primary and secondary hydroperoxides to the corresponding carbonyl compounds, both homogeneously and heterogeneously (187—191). The mechanism of chromium catalyst interaction with hydroperoxides may involve generation of hexavalent chromium in the form of an alkyl chromate, which decomposes heterolyticaHy to give ketone (192). The oxidation of alcohol intermediates may also proceed through chromate ester intermediates (193). Therefore, chromium catalysis tends to increase the ketone alcohol ratio in the product (194,195). 

Catalysts used for preparing amines from alcohols iaclude cobalt promoted with tirconium, lanthanum, cerium, or uranium (52) the metals and oxides of nickel, cobalt, and/or copper (53,54,56,60,61) metal oxides of antimony, tin, and manganese on alumina support (55) copper, nickel, and a metal belonging to the platinum group 8—10 (57) copper formate (58) nickel promoted with chromium and/or iron on alumina support (53,59) and cobalt, copper, and either iron, 2iac, or zirconium (62). 

Chromium is highly acid-resistant and is only attacked by hydrochloric, hydrofluoric, and sulfuric acids. It is also resistant to other common corroding agents including acetone, alcohols, ammonia, carbon dioxide, carbon disulfide, foodstuffs, petroleum products, phenols, sodium hydroxide, and sulfur dioxide. 

Alkyds. Alkyd resins (qv) are polyesters formed by the reaction of polybasic acids, unsaturated fatty acids, and polyhydric alcohols (see Alcohols, POLYHYDRic). Modified alkyds are made when epoxy, sUicone, urethane, or vinyl resins take part in this reaction. The resins cross-link by reaction with oxygen in the air, and carboxylate salts of cobalt, chromium, manganese, zinc, or zirconium are included in the formulation to catalyze drying. 

Concentration Effects. The reactivity of ethyl alcohol—water mixtures has been correlated with three distinct alcohol concentration ranges (35,36). For example, the chromium trioxide oxidation of ethyl alcohol (37), the catalytic decomposition of hydrogen peroxide (38), and the sensitivities of coUoidal particles to coagulation (39) are characteristic for ethyl alcohol concentrations of 25—30%, 40—60%, and above 60% alcohol, respectively. The effect of various catalysts also differs for different alcohol concentrations (35). 

The formation of an epoxyketone (1) is generally favoured when the expected product of oxidation of an allylic alcohol is a cisoid enone. This type of reaction is promoted by acid conditions and may be prevented by using the chromium trioxide-pyridine reagent which gives only the unsaturated ketone (2) corresponding to the starting alcohol. ... 

When a solution of chromic and sulfuric acids in water is added at 0-20° to an alcohol or formate dissolved in acetone, a rapid oxidation takes place with the separation of the green chromium III reduction product as a separate layer. This system is commonly known as Jones reagent. The rate of oxidation is so fast that it is often possible to run the reaction as a titration to an... 

If homolytic reaction conditions (heat and nonpolar solvents) can be avoided and if the reaction is conducted in the presence of a weak base, lead tetraacetate is an efficient oxidant for the conversion of primary and secondary alcohols to aldehydes and ketones. The yield of product is in many cases better than that obtained by oxidation with chromium trioxide. The reaction in pyridine is moderately slow the intial red pyridine complex turns to a yellow solution as the reaction progresses, the color change thus serving as an indicator. The method is surprisingly mild and free of side reactions. Thus 17a-ethinyl-17jS-hydroxy steroids are not attacked and 5a-hydroxy-3-ket-ones are not dehydrated. 

---