Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Ceramics lapping

Ruiling, Zeng, Acoustic emission investigation of ceramic lapping process, MS Thesis, Kansas State University, Manhattan, Kansas, 1998. [Pg.194]

A new model for material removal mechanism was proposed based on the experimental evidences. The "Double Fracture Model" was proved in the stock removal mechanism of ceramics lapping. [Pg.261]

Chapter 8 also comes from the Precision Micro-Machining Center and presents a modem technique for monitoring the ceramic lapping process acoustic emission (AE). AE is well known as a tool to monitor the ceramic grinding process however, there are only a few studies regarding AE in the lapping process. [Pg.374]

A diamond-finishing operation normally has as many as three steps, with a different grade of diamond used in each. Most stock removal is performed in step 1 and/or 2. The required surface finish is produced in step 2 and/or 3. In the case of seals, where the ceramic component is finished on a ceramic lap, a single grade of diamond will usually do the job. [Pg.753]

Yoon TH, Arnold CA, McGrath JE (1989) Titanium 6/4 single lap shear adhesive performance of polyimide homopolymers and poly(siloxane imide) segmented copolymers. Mater Res Soc Symp Proc 153 (Interfaces Polym Met Ceram) 211... [Pg.102]

The ceramic based on lead zirconate (PZ) has intermediate figure of merit values. Its final form as a thin plate is obtained by sawing up a hot-pressed block and lapping and polishing to the required dimensions. Similar methods must be applied to single crystals and so the costs of manufacture are not very different. [Pg.421]

Use Wear resistant filler, thermal conductor in compounds, high temperature paints, ceramics, refractories. As a polishing and lapping abrasive. [Pg.493]

Properties Wh. coarse hexagonal powd. 175 mean particle size dens. 1 g/cc (lap) surf, area 2 m /g Boron Nitride HCP [Advanced Ceramics]... [Pg.130]

A lapping system equipped with a 15 in. copper lap plate and an electronically controlled diamond slurry dispenser was used in this research. A 3 xm diamond slurry was employed, which produced higher and more stable material removal rate than a 1 pm diamond slurry. The slurry was applied at a rate of 3 sec of spray every 30 sec. The lapping pressure on each ceramic test bar was 35,700 Pa. A sample carrier accommodated five test bars arranged aroimd the outer perimeter of the carrier. [Pg.93]

For determining the depth of damage caused by the grinding of RBSN and zirconia-toughened alumina, the ceramic materials were first ground under a range of grit depth of cut conditions and then lapped to establish the depth... [Pg.94]

Flexural strength vs. depth of material removed by lapping for RBSN ceramic with original surface ground at (a) pm, (b) = pm, (c) fw = 0.29 pm,... [Pg.102]

Flexural strength versus depth of material removed by lapping results for zirconia-toughened alumina ceramic are shown in Figure 4.11a through... [Pg.102]


See other pages where Ceramics lapping is mentioned: [Pg.247]    [Pg.247]    [Pg.11]    [Pg.512]    [Pg.94]    [Pg.263]    [Pg.236]    [Pg.429]    [Pg.450]    [Pg.34]    [Pg.11]    [Pg.876]    [Pg.881]    [Pg.389]    [Pg.160]    [Pg.284]    [Pg.459]    [Pg.25]    [Pg.421]    [Pg.426]    [Pg.11]    [Pg.626]    [Pg.85]    [Pg.797]    [Pg.736]    [Pg.837]    [Pg.933]    [Pg.130]    [Pg.6]    [Pg.7]    [Pg.178]    [Pg.413]    [Pg.673]    [Pg.734]    [Pg.52]    [Pg.92]    [Pg.93]    [Pg.95]    [Pg.101]    [Pg.102]   
See also in sourсe #XX -- [ Pg.247 , Pg.248 , Pg.249 , Pg.250 , Pg.251 , Pg.252 , Pg.253 , Pg.254 , Pg.255 ]




SEARCH



Lapping

© 2024 chempedia.info